Models > JVM2070SH001 > Instructions

JVM2070SH001 General Electric Microwave - Instructions

All installation instructions for JVM2070SH001 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM2070SH001
16-30 of 160
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

tray broke

  • Customer: martin from the villages FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 16 people found this instruction helpful
replace tray

Noise and no Heat on Microwave oven.

  • Customer: Luis from Plano TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 16 of 25 people found this instruction helpful
First, I waste $65 by calling some "REPAIR" service. They showed at home and charge me that just to tell me
Second, I researched on the web and ordered a part, which was not the issue. I waste abnother $72
Third, I found Part-Select and got the right answer: the Diode was the problem. Ordered the part form Part-Select and it FIxed it !!!

Note: I did not buy a new microwave because this one is mounted on the wall and it will cost me +$800 just the lowest price.

Grille holding venting mechanism broke

  • Customer: Kyle from Castro Valley CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 12 of 14 people found this instruction helpful
First, I removed the two phillips screws on the top of the microwave. Then I was able to take the venting mechanism off of the microwave. I unscrewed all of the parts attached to the broken plastic vent and reattached them to the new plastic vent. Once all the parts were on, I simply put the venting mechanism back onto the microwave and placed the two phillips screws back to hold it in place. Lastly, I reattached the springs that allow the vent to close. A simple job done in less than 15 minutes.

Microwave Fan Turned on When Door Was Opened

  • Customer: Bishop from Coupland TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 13 of 17 people found this instruction helpful
To get to the switches you need to remove the metal cover/housing of the microwave, by first removing several screws that hold it in place, and then sliding the cover towards the back of the unit. You'll find the switches in some plastic holders above the door-open button, and it's its easy to see how the mechanism engages/disengages the switches when the door is opened and closed.

If it is not obvious which switch is bad, in our case the bad switch felt "soft" when we pressed the switch button with our fingers. A good switch has a firm "click" when pressed.

The switches are easy to replace - pop out the old switch (no tools required) and pull off the electrical connectors. Then pop in the new switch and reattach the connectors.

I diagnosed the problem incorrectly: based on a previous repair.

  • Customer: Ralph from Brandon FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 26 of 57 people found this instruction helpful
The old fuse is perfectly good. The new ones arrived within a day.

No heat in the microwave

  • Customer: Douglas from Mechanicsburg PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 13 of 19 people found this instruction helpful
We purchased our Microhood oven about 4 years ago along with the extended warranty package offered thru home depot. Within one year, the problems began. Each year the secondary switch would go bad rendering the microwave useless. If you have 3 small children like we do, you tend to use it a lot. We sure take the microwave for granted.

Each time G.E. would fix the problem at no charge. Ths time - the warranty had expired and GE wanted to charge us $80.00 for service call plus parts and labor. We estimated the cost to run at least $150.00 or more.

To top it all off, GE was going to have a service tech avail for over 2 weeks. This is poor customer service and completely unaccceptable.

Because this was a recurring problem, I figured it was the same part that had being going bad since we purchased the appliance. I decided to order the part "secondary switch" myself and attempt to fix the microwave on my own.

I ordered the part last Tuesday, the part arrived last Friday. Within 10 minutes I had the microwave apart, replaced the part and had the microwave back in working order.

PartSelect saved me over $100.00.

We are very satified with PartsSelect, I would recommend them to anyone

halogen bulb burned out

  • Customer: Thomas from Wake Forest NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 14 people found this instruction helpful
*Remove Two Phillips head screws from the top of vent slide the vent left to remove it. Take the charcoal filter out then the metal cover underneath the filter. It also has a phillips head screw. bulb socket is on right facing down. Squeeze the metal clips and remove socket from bracket. Installation is the reverse of removal.

Everything worked on the microwave, except it would not heat anything.

  • Customer: Randy from Ottawa IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 14 people found this instruction helpful
The microwave had been working fine until one day when the timer counted down but the heating motor (or whatever you call it) would not come on. So the timer would count down but nothing inside would get hot. I did not know what it was for sure but decided to take it apart and look. Once I had the control panal off, I found three small wired switches inside. One of these switches appeared to have shorted out. So I searched online and found Partselect.com. I found a matching switch , ordered it (arrived in couple days), put it in, and VOILA it works! Thanks Partselect.com.

Filter needed replaced

  • Customer: todd from greensburg PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 14 people found this instruction helpful
Remove two screws,slide panel to left and remove,install filter.Replace panel,and done.Service call would have cost $97,98. EH? No brainer!

GRINDING NOISE IN MOTOR

  • Customer: MARK from VALLEJO CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
REMOVED UPPER COVER. REMOVED SCREWS IN COVER PLATE & MOTOR MOUNT. REMOVED INNER COVER WITH POP SCREW INSIDE MICROWAVE. REVERSED PROCEES TO INSTALL NEW MOTOR.

i was using the microwave one evening, and the vent door in the top front of the oven just snapped, and pieces were every where, plastic, springs, little metal hinges, and i just stared in amazement.

  • Customer: Charles from Dover DE
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
first thing i did was to mistakenly go to GE's website to order the part, after the part was sent to me broken, and that was in february, i finally received the reimbursement for the part 4 months later. the part was $40.00 less on your site than GE's.
Overall, there were two screws that held the old grille in place, i removed them, and reassembled all of the springs and then reattached. i am so thankful that i found your website, and will do business with you again! Chuck Luton

Oven blows 20 amp fuse

  • Customer: PATRICK from Covington LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

Broken light lens for the light bulbs

  • Customer: TERRELL from OAK POINT TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
Took the screw out of the glass door holder, bent the clips up and removed the broken glass. While this was open chenged the light bulbs as well. Put new glass in bent the holding clips down and closed the doors and installed the screws again. So nice to have good light again and also new glass in them. Never noticed they were broken before.

BY THE WAY PARTS SELECT IS VERY PROMPT AND I RECEIVED MY PARTS IN ONE DAY AFTER THEY SHIPPED. SHIPPED ON MONDAY GOT THEM TUESDAY, thanks parts select for your promtness and speedy work for shipment.

Two counter light bulbs burned out

  • Customer: Jerry from Rio Vista CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
After removing the screws holding the 2 cover plates in position, I removed the halogen light bulbs with my fingers. Then I placed a paper towel around the first replacement bulb and lined up the two wire connectors with the two holes in the receptacle. I pushed in, but the bulb's probes did not slide into the receptacle. I spent five minutes aligning and pushing but to no avail. Then I removed the filter screen on the side of the receptacle, shined a flashlight beam on the receptacle, and with an improved view of the two holes in the receptacle, slid the bulb in. The second bulb was inserted in a few minutes, and the job was done. Whoever designed the halogen bulb was not as bright as Thomas Edison.

the halogen light above the stovetop burned out

  • Customer: John from ORLANDO FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
the online instructions were ideal - just unscrewed the right-hand screw (the only screw) and replaced the bulb by inserting gently but firmly)...getting the old bulb out was a pain, b/c it shattered in my grasp (with little bits of glass all over the stove!), but that has nothing to do with the purchase and installation from this site - all a very good experience
All Instructions for the JVM2070SH001
16-30 of 160