Models > JVM2070SH001 > Instructions

JVM2070SH001 General Electric Microwave - Instructions

All installation instructions for JVM2070SH001 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM2070SH001
46-60 of 152
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Light for cooktop burned out

  • Customer: Bryan from South Beach OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Opened cover, pulled out old bulb, inserted new one, put cover back on. I was out of town when bulbs arived, my wife put it in. She said it was easy.

lens was not sized to fit and was left extremely sharp

  • Customer: robert from salmon ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
HAD TO TAKE TO A LOCAL GLASS SHOP FOR SIZING AND TO REMOVE SHARP EDGES. WILL NEVER ORDER AGAIN.

broke glass turntable

  • Customer: dennis from longbeach CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
just set the glass turntable in and bingo it worked
no tools needed. thanks for such a fast delivery
sincerly dennis and chris delbello

Microwave would not go on

  • Customer: Jim from Lincolnshire IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
All electrical worked (fan, lights, control panel) door switch was broke. Pulled the oven out. Took out two big screws from the cabinet above. (be careful not to drop oven)Set the oven on kitchen counter. Took off five screws that held the vent cover. Removed vent cover. Took out one screw that held the control panel. Lifted, turned and slid the panel into the space below so I could get to the upper door switch. Replace door switch and re-assemble.

Microwave would turn on when door opened

  • Customer: Lois from El Segundo CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!

broken lens

  • Customer: greg from bellingham MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
first i remove the screw, then removed the lens assembly (really a frame) bent the feet out of the way, slid the old lens out and the new one in, bent the feet back in place and inserted the assembly into place replaced screw. the killer is a day later it was broken again, think the lens can't handle the heat from the oven below or the lights above. you guys where great fast and exact match part but the ge design is flawed

Both my microwave halogen lamps went out.

  • Customer: Vincent from Mount Sinai NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Using a phillips screwdriver I opened the panel in which the two lamps are located and easily removed the lamps. I ordered them through the internet and was pleasantly surprised when I received them the next day.

Micrwave won't run - turntable turns backwards when door opened...

  • Customer: Roger from Fountain Hills AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...

broken tray

  • Customer: Juan from Torrance CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Open the box that the part came in and place it in the microwave. The best is how fast it came to my home. Thanks

microwave would not start

  • Customer: JULIA from JACKSONVILLE FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
took of cover removed switch and replaced with new one

After closing door the display panel must be tapped on to keep the unit operating.

  • Customer: Paul from San Jose CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
The switches are not the problem! The problem is in the tolerences of the latch housing. I have ordered two new housings (Upper & Lower) and will see if the tolerences are closer. If not I will try epoxying a shim to the plate that operates the microswitches. The other option is to file the mounting slots of the housing to allow adjustment, which would be iffy,keeping them from moving with use. The exploded drawings really need to be clarified. The scale is way too small. It was extremely difficult to pick out the individual parts of the mechanisiam.

VENT GRILL FRAME JUST FELL APART

  • Customer: DONALD from NEW PORT RICHEY FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
I CONTACTED GE , WITH ABSOLUTELY NO HELP, THANKS TO PART SELECT I WAS ABLE TO ORDER THE PART AND RECEIVED IT WITHIN 4 DAYS
IT WAS VERY EASY TO TAKE APART, FIRST UNSCREW THE SMALL PHILLIPS SCREW ON THE TOP RIGHT SIDE , THEN SLIDE THE VENT GRILL TO THE LEFT AND GENTLY PULL AWAY FROM THE MICROWAVE, THAT'S ABOUT IT AND INSTALL IN THE SAME MANNER.

Broken glass microwave turn table

  • Customer: Serio from Lansdale PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
The new turntable shipment was super fast!!! I received it only a few days after ordering it. Installation was nothing more than placing it in the microwave oven.

GREAT Transaction!!! Thanjs!!!

Tray was brokenwhen moving

  • Customer: Gene from LaPorte IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
opened the door and put in the tray!

CRACKED MICROWAVE GLASS PLATE

  • Customer: marielen from newport RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
ODERED REPLACEMENT
All Instructions for the JVM2070SH001
46-60 of 152