Models > JVM1860SF001 > Instructions

JVM1860SF001 General Electric Microwave - Instructions

All installation instructions for JVM1860SF001 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM1860SF001
46-60 of 381
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Halogen light for the Microwave above the stove went out.

  • Customer: Darren from Madison CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Ordered the part. 2 days later part arrives. Took me 30 seconds to install the part. Sorry it was not more eventful.

Lamp burnt out

  • Customer: Robert L. from Racine WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
We had our kitchen remodeled; new cabinets, countertop, range, refigerator, microwave, dishwasher and floor.

The cabinets around the microwave were custom made; it looks great but it hid the screws, which had to be unscrewed to remove the grill so the interior light of the microwave could be replaced.

A stand was used to support the microwave as I lowered it so the screws could exposed so the light could be replaced.

The light was replaced, the microwave was raised back into place and all is well. I replaced the bulb while my wife was out of town. When she returned she noticed that the microwave was nice and clean; she was NOT aware of the fact that the bulb was replaced!

Bob
Racine, WI

Grille assembly vent was cracked and would not stay in place nor would vent operate

  • Customer: Eric from Shiloh IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
By selecting the entire grille assembly vs buying just the individual parts it made the replacement simple. Just had to remove 2 screws from the old assembly to remove. The new assembly popped right in and fastened it with the 2 old screws. I would recommend purchasing the entire grille assembly vs. just the individula parts if the plastic is cracked and brittle. The price difference was not that significant.

A ratteling when the over was running

  • Customer: Clay from Kansas City MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Unplugged the stirrer motor and the noise stopped. Therefore, replaced the stirrer motor.

The handle broke

  • Customer: Amado from The Villages AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 7 of 13 people found this instruction helpful
After prying off the outer cover in the back of the microwave door with a plastic spatula; had some difficulty to avoid breaking it. Removed the remaining part of the door handle. Then attach the new handle. Replace the plastic outer cover; noting the attachment clips.

Turn table stoped functioning

  • Customer: Cody from Omaha NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
Troubleshooting process:
Using a screw driver I opened the bottom of the unit using a Philips screwdriver and unhooked the drive motor electrical connector. Using a multimeter I checked to ensure power to the motor. This confirmed that the motor is bad and must be replaced.

Repair process:
After receiving new motor I removed the old motor and installed the new one using a Philips screwdriver and closed up the bottom cover.

It functioned good as new. Relatively cheap and very easy fix.

Microwave would not go on

  • Customer: Jim from Lincolnshire IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
All electrical worked (fan, lights, control panel) door switch was broke. Pulled the oven out. Took out two big screws from the cabinet above. (be careful not to drop oven)Set the oven on kitchen counter. Took off five screws that held the vent cover. Removed vent cover. Took out one screw that held the control panel. Lifted, turned and slid the panel into the space below so I could get to the upper door switch. Replace door switch and re-assemble.

Oven blows 20 amp fuse

  • Customer: PATRICK from Covington LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

Replace spent carbon filter

  • Customer: NOSHIR from Sun City Center FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
remove 2 screws from top of grille; remove grille by moving it to the left and then away.
remove old filter by lifting the front edge and then pull out, and replace it wih a new one using the reverse order of the above.
replace grrille and screws.
The repair is a 'no brainer'.

Both undercabinet light bulbs blown

  • Customer: pete from roslyn NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
1. Open the cover over light bulbs with screwdriver.
2. Pulled out blown bulbs.
3. Inserts new bulbs from Partselect.
4. Tested new bulbs
5. Closed the cover over light bulbs with scvrewdriver.
6. Threw out old bulbs and packaging material.

Now, was that easy or what!

Halogen lamps needed replacement

  • Customer: Don from Wildwood MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Easy to repair. One screw, remove bulbs, replace with new ones, secure screw.

Partselect.com shipped items quickly as promised, provided follow up email confirming receipt of order, a second email confirming shipment & a link to check shipping status.

Would not hesitate to do business with Partselect.com again!!!

handle on microwave broken.

  • Customer: Terri from Fort Collins CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 14 people found this instruction helpful
removed panel and unscrewed old handle and replaced. The only complaint I would have if maybe it came with some directions.

Lamp burned out.

  • Customer: Gregory from Gastonia NC
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Removed one screw, removed cover, and replaced lamp. Pretty straightforward.

Grill Assembly flew out

  • Customer: Dino from Chula Vista CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
My GE JVM1870SF02's vent assembly was on its last leg and it finally popped off and fell. I was glad that I was able to buy the specific part and having the Blown-out diagram helped to narrow which part I really needed to purchase.

Removed the Grill Assembly front-flap panel off broken grill. Installed the front-flap panel on new grill assembly and installed in the top section of the microwave. Good to go!

Light for cooktop burned out

  • Customer: Bryan from South Beach OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Opened cover, pulled out old bulb, inserted new one, put cover back on. I was out of town when bulbs arived, my wife put it in. She said it was easy.
All Instructions for the JVM1860SF001
46-60 of 381