JMW8527DAS Jenn-Air Microwave Oven Combo - Instructions

First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.

Remove the oven door. Remove 3 self tappers on rear wall of oven to take off a round access panel. Pull out a pre-cut rectangle of insulation. Next I removed the 2 screws holding the sensor in place. Pulling the sensor out a bit told me I was "touching" the correct wires in the SMALL rectangular opening. The wires are not visable and 2 hands do not fit in this small opening.I looked at the NEW sensor to see the release on the sensor plug. Slip the angled needle nose into the opening and grasp the plug/release side. The plug pulled apart easily. The sensor wire pulls out with a little bit of twisting to fit it out the hole. The new plug pushes in and has to be worked down to where you can reach it. The same angled plier works to re-attach it. It takes longer to read this than to do the job. Best of luck, Al

I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me.
The parts was delivered almost before my notice they were shipped.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Found instruction on internet,
1. Remove anit-tampering screws with punch and hammer
2. Remove the rest of the screws
3. Removed cover
4. Remove burned out bulb and installed new one
5. INstalled cover
6. Installed screws including the anti tampering onces
7. Op tested unit.
Wife is happy.

Make sure to have your model number correct. First tray I purchased I didn't use the model number and just picked what I thought would work (KitchenAid), but didn't. Second attempt I put in the model number and received the correct one. Take out of the box and into the oven, that easy.

1. Removed cabinet screws (10-15?). 2. Removed cabinet. 3. Removed top interlock switch which actually was not defective. The press clip connection appeared as if it had been arcing for quite some time and the corrosion created resistance sufficient to prevent the current from getting through the switch. 4. Replaced switch anyway but broke plastic retaining clip despite every effort not to do so. Reset broken clip with super glue. 5. Reassembled cabinet and appliance is in good working condition.

Problem would come and go. Found service schematic inside unit. Perform all the suggested tests. One possible solution was the primary interlock switch shown on the schematic and a check found the switch stuck. It would free up some times but would stick again in the open position. Ordered switch which was a simple plug in unit.

Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

Replaced diode works great. your website said 92% diode was problem and it worked. Order fuse in case old was blown did not have to use it.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

We have a Jenn-Air microwave and oven combination that is installed as a "stack" in a cabinet. The light bulb had burned out, and I read some of the posts on the partselect.com site about how others performed this replacement; ours was a bit different.
To replace the microwave light bulb, we had to remove the entire microwave and oven stack from the cabinet. There were four anchor screws on the sides (two on each side) of the microwave that were driven in perpendicular to the face of the microwave. There were four more screws that were on the sides of the oven that could be accessed once the oven door was open.
With those anchor screws removed, we had to carefully pull the entire microwave / oven stack from the cabinet to reach the top cover of the microwave. We used an old wooden crate to hold the front of the oven and left the back of the oven resting in the cabinet enclosure. This gave enough room to access the screws on the top cover of the microwave, without having to lift the entire stack down to the floor.
At this point, I could unplug the microwave power cord, which was plugged in to a socket built into the top of the conventional oven part of the stack.
The top cover of the microwave was attached with regular Phillips head screws, so those were easy to remove. Several other instructions indicated I would need a torx or star drive screwdriver, but I did not.
Once the screws were removed from the top cover of the microwave, the cover can slide rearward to be removed. However, there are two metal strips that run vertically along the sides of the microwave and at the top of the microwave, these bends over at a right angle over the top of the microwave. The top cover has tabs that sticks up vertically from the cover, so that the bent strips prevents the cover tabs from passing as the cover is slid backwards. The vertical strips have several screws connecting it to the body of the microwave. On one of the vertical strips, I removed the two of these screws closest to the top of the microwave. Then, I gently pushed a wood chisel, because of the bevel angle, between the vertical metal strip and the microwave body. This moved the bent-over portion of the vertical strip far enough away from the microwave that the tab on the top cover cleared the strip, and I could then remove the top cover.
With the top cover removed, I could see the old light bulb. It is attached with a push-in electrical connection that was easily pulled off. One Phillips head screwdriver held the old bulb in place towards the rear of the microwave. Towards the front of the microwave, a small plastic post holds the front of the bulb. I removed the screw and pulled out the old bulb.
The new bulb fits easily into the same plastic post and screw connection. However, the new bulbs connector prongs are bent at a 90 degree angle to the original bulb. Instead of sticking straight out from the microwave, which was how the old bulb was configured, the new bulb prongs pointed to the right side of the microwave (as viewed from the front). Fortunately, the wiring harness in the microwave that connects to the light bulb had a zip tie that was loose enough to get enough slack for the push-in connector to reach the new bulb's prongs.
After the bulb was in, I reversed the steps described above, making sure to leave the chisel in place until the top cover had been secured back in place. Once the chisel was removed from the vertical metal strip, the bent portion again would prevent easy removal of the top cover. I made sure to plug the microwave power cord back into the outlet on the conventional oven, then we slid the entire unit back into the cabinet enclosure, and I put the anchor screws back to hold the stack into the cabinet.
Three of us worked on this - mostly to help pull the stack out of the cabinet and to help steady it while the front was resting on the wood crate. This is not a single-person job. It was not terribly difficult, but the number of steps is very tedious. I found a helpful YouTube video "How to uninstall/install a Jenn-Air JMC8127DD/JMC8130DD Microwave Oven" posted by Ali The Handy Man. Being able to see that the microwave and oven stack was connected by a "bridge" (as Ali calls it) was a major help in tackling this.
After this, we suspect that Jenn-Air must have not wanted any repairs to their appliances. As I said above, this repair to replace a light bulb seemed unnecessarily tedious.

I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.

Removed both oven doors to remove from the wall. Pulled the oven out of the wall. Removed all the sheet metal backing on the back of oven top and bottom. Removed the electrical,connections to the fan. Removed attach,net screws and pulled the fan. A bit of a pain had to twist pull and bend the metal bracket. Replacement fan had to be reversed came apart easily and reversed then reassembled. Fit in easily and attached electrical connections. Then reattached all the sheet metal backing bottom then top. Put oven back in wall then secured in place. Re installed the doors and applied power. Oven worked great as soon as we tested it. Great fix, works better than new!