JGS8750ADB Jenn-Air Range - Instructions

took out racks removed 2 screws holding igniter removed 4 screws on back of stove and unplug igniter. reversed the order installing the new one

So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is like new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.

Put a new one in.

Installed new spark module by removing back panel of stove. Removed two screws holding old module. Disconnect lines, marking colors. Installed new. Problem not solved. Out $128 since new module was not returnable after install.
Called Judd and Black service department. Tech came on service call. Said it was bad gas valve. They ordered part. Than needed two weeks to install. I installed it and problem persisted. Could not return part because I installed it myself. Out $180. I had cleaned ignitor with alcohol from top. Took apart cooktop and cleaned from bottom. Problem fixed for free. Out over $500 in parts and labor.

slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.

Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

slide latches in rear of floor panel forward and remove.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.

1. Remove the oven door by opening a few inches and lifting straight up. Remove racks to access it. 2. The old igniter is just held in by two nuts that have a screw head in the middle of them so they could be removed by a nut driver or by a screwdriver. Unfortunately, both of our screws threads were terribly stripped and after first trying to use pliers to help remove them, we ended up using a dremel tool to cut them off. 3. unplug the old igniter and take it out. 4. Plug in the new igniter. 5. attach the two screws. (our time on the repair was mostly spent trying to find two screws around our house that would replace the two that were stripped--otherwise this would have been 15 minutes). 6. return the door and racks by the sliding the door downwards onto the hinges

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

Watch the video. Spot on instructions. Easy peasy.

Considered calling a repair facility, after reading your tips and what parts should fix what problem I decided to fix myself. Moved oven out,slide in gas range. Took off probe and tested with volt ohm meter, read 1090 ohms, should have been good. I could see oven igniter glow red, but I decided to replace both units, glad I did. Oven go's from 100' to 350' in 8 minutes now, for less than $85.00 have a fully functioning oven now. I'm sure the repair would have exceeded $300.00 or more being we live in a rural area. Thanks for the tips from your experts as well as you customers.