JGR8875QDS Jenn-Air Range - Instructions

i ordered the part, it came in speedy quick,and it was very easy to install i saved $200 bucks, and my mom was the happiest person in the world. thank you.

My stove would take forever to preheat and sometimes it wouldn't heat above 175. I order a new igniter, which was located under the drip pan . It took less then ten mins to replace and the stove is working like new.

We hired the neighborhood handy man, and he was able to repair the oven in about 15 minutes. I order the part and received it the next day. Excellent Service!!

i got the right part from u fast del.and had it fixed in 15 min. was very happy withu service thank u will buy more parts from u when i need them it was the same part i took out

First i removed the two screws that hold the element in place. I then pulled the wire out of the hole and disconected the plug. then plug in the new one, put the two screws back in, and checked it to see if it worked,It worked like a new one! So as my reward my wife baked me cookies!

Removed plate at bottom of oven and unscrewed ignitor. Tipped oven forward and removed tiny back panel to reach plastic socket that disconnected ignitor from oven. Pulled ignitor out and awaited replacement part and did reverse steps. Oven ignitor worked right away.

For stovetop I ordered part and removed sheet metal screws from oven rear top panel after appliance was pulled from wall, gas and electrical disconnected. I pulled old spark ignitor module out and transferred colored wires to new module and snapped that into place. Replaced oven and presto, stovetop ignitors worked immediately.

Screws that hold the burners in place where rusted and the tops broke off, After breaking the tips of two cross screwdrivers, result was that I had to drill out old screws and re tap new holes into the base of all the gas outlets. As this was a second hand stove. I am not sure what cause the screws and the gas outlets to become extremely rested. It should of been possible in my mind to just insert a tool and remove the pilots, But three of the burners only has small openings, so it was not possible to do this, A three minute job, took well over an hour.

It took all of 10 mins. Open oven door slightly lift to remove.took out shelves and bottom of oven,lift at back to remove.Two screws hold the Igniter, was able to pull the connector into the oven to change. Oven works great!

Removed door from oven. Removed 6 screws to dismantle door. Removed 3 more screws to remove hinge from door...reverse order to assemble.
Very easy

Removed the two screws pulled the element out and unhooked the wires then used one of the included adapters to reinstall the new sensor then screwed the two screws back in to secure the sensor. Everything works fine now.

This is simple for most people - unscrew and remove the bottom oven floor pan. There is the igniter, removed with two screws with a 1/4 nutdriver. However, my problem was that when I unclipped the old igniter, I dropped the over part of the connection, it fell down the hole, through the insulation, to the bottom of the stove where the wiring is. I had to pull out the stove to get to the connection, push it back up the hole to the oven, then install the igniter. My advice: do no lose your grip on the oven wire whatever you do. Otherwise, it was a snap, even for a klutz.

Replaced igniter, removed inside bottom cover 2 screws,removed igniter 2 screws & unplugged igniter from back of oven after removing plate with 1 screw. Could not have been any easier took less than 10 minutes. And doing business with PartSelect was great, would recommend and use again any chance I get.

I have and in the wall Magic Chef oven CGW3330ADW seriel 10799876US that came the purchase of my home 10yrs. ago. After a black out and 2 brown outs my oven would not start and the F3 code is beeping and the "door lock" light was on but the door was unlocked. The clock was working fine, but could not use the timer or set the temperature. I googled "FLASHING F3 code" and one of the results was the comment thread on the Parts Select website. When I clicked the link I read several customers sharing their story that was very similar to mine. I was able to click on a video and see a short demonstration on "HOW EASY" it was to replace the "Short Oven Sensor Kit." I though, "Yea right!" I left a comment on that You Tube video with my make and model and a brief explanation of my problem. I received a reply to my comment with in 24 hours, confirming what other consumers had shared...The "Short Oven Sensor Kit" was needing to be replaced. I ordered the part for around $30 VERY late on Thursday evening and when I woke on Friday morning, I a shipping confirmation email. I received it VERY early on Saturday morning! I was able to replace the part very easily with in about 10 minutes. I was VERY LUCKY that I was able to to the repair WITHOUT having to remove the oven for the wall! I would have had to pay for help if I had to remove it from the wall. The Parts Select web site save me over $400 which was the estimate for the parts and labor from a local appliance repair business! I was told that it would probably be cheaper or about the same as buying a new over which was their recommendation. I am so glad that I decided to do the research and in less that 1 hour I had my order placed. Thank You Parts Select!

removed two screws from ignitor, pulled connector from hole behind it, replaced ignitor, reconnected. tried the oven and it worked first time. easy, easy.

Removed the racks inside the oven then (2) screws that hold the bottom cover. Once the cover was off I exposed the burner element. I Removed (2) small Philips screws that held the unit. I removed electrical plug and the unit was out. I replaced the part and put everything back together. This was a very simple job took me about 10 minutes to complete. gas company wanted to charge $130 just to come out and look at. I saved some good cash.