JGR8850ADQ Jenn-Air Range - Instructions

Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. The order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

My wife called a service company and was told that a tech would have to inspect the stove.
service charge 60.00 After inspection the parts would be orderd and a 200 fee for labor plus the parts would be charged at the completeion of the job. 2 weeks for part. I found you on the net orderd the glass. got it in 2 days and I completed the repair in 20 mins. Cost 89.00

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor

I had to unscrew 4 screws on the burner unit and then 2 screws on each igniter. slip the olds out and the new ones in and then replace all the screws. And wa la they sparked and I was cooking again.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine.
Very Easy!

I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

Remove the oven racks. Slide the two catches, located at each rear corner of the oven bottom, toward the front of the oven.

Lift the rear edge of the oven bottom slightly, then slide it back until the front edge of the oven bottom clears the oven front frame. Remove oven bottom from oven.

Pulled storage drawer out to the first stop position. Lift up front of drawer and pull to the second stop position.
Grasp sides and lift up and out.

Under storage area, I removed two screws to remove a steel plate. In the oven, I removed two screws that held on the Oven Igniter. Unplugged the Igniter under the storage area.

Plugged in the new Oven Igniter, replace the two screws that held the Oven Igniter, replace the two screws for the steel plate. Put the storage drawer back, the bottom of the oven back and the racks.

It was easier than I though it would be.

Opened the box and removed the rack!! It's well-made, though not perfectly flat. But it works well in the convection cycle of the Jenn-Air which has a "drying" mode within the cycle. I've done basil and chives so far. The dealer from whom I bought the dual-fuel downdraft range did not mention the rack as an option. I found out about it through the range's manual. Great, quick service from PartSelect.

The repair was easy. Partselect processed my order quickly and my part was delivered sooner than I expected.

Removing the old igniter was simple. I took off the oven door to create easy access to the oven. I then unplugged the connection and removed the screws that held the older igniter in place. Installing the new igniter was almost as easy. I followed the same steps as above, but in reverse. I accidentally dropped one of the screws, so installation probably took 1 minute longer than removal. :)

I'm a very satisfied customer.

Turn off the gas supply and unplug the power cord. Remove the screw on the back plate for the metal tab that covers the valve. Bend the tab up to expose the valve. Remove the gas line that feeds the broiler with an adjustable wrench. Remove the mounting screw for the valve. Loosen the valve inlet gas line fitting with an adjustable wrench. Lift the valve out. Reverse the steps to install the new valve.

After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.

Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...

It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison

I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.