All Installation Instructions for General Electric Cooktop JGP336CED1CC

Burner igniter needed to be replaced

Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off.
Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way.

Parts Used:

Surface Burner Spark Electrode

Thomas from Bloomsbury, NJ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

37 of 63 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip pans needed to be replaced.

Simiple repair. Determined drip pan size (sm, med., lg.) removed 2 screws holding drip pan, placed gasket around new drip pan and installed. Repaired took less than 5 minutes.

Parts Used:

Burner Bowl Seal

Steve from Broken Arrow, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

18 of 26 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

electronic ignitors would not stop firing even when burner was off

first I removed all the srews from the burners that hold the glass cooktop. I then disconected the two wires from the damaged gas valves and replaced them all four with the new ones. After that I put it all togehter and work just fine and celebrated with a good cold beer.

Parts Used:

Gas Valve Switch

Jorge from Tulsa, OK
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

12 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Spark module was not working correctly

I unscrewed the burners which was three screws per burner then removed gas control knobs and pulled up range top and un hooked the old module and replaced it with the new one two screws hold it in place and connected it the same way the old one was and put range back together and now it works perfect and saved me over $250.00 and part only coated around $40 with shipping great parts seller and I highly recommend partselect.com very easy fix thanks

Parts Used:

Spark Module - (4+0)

VINCENT from CYPRESS, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

9 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replacement cook-top, had natural gas orifices, needed propane

Three were simple screw out and replace with a nut driver. The warming burner had a smaller opeining which was too large for the nut driver. Had to remove shielding aroound it first. Simple, job. My mother did the last one.

Parts Used:

Single Liquid Propane Orifice Spud - Medium Burner

Aloha from Monterey, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

9 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Electrode ceramic insulator was cracked

First I elevated range top, then removed cracked electride from connector pin. Installed new electrode and lowered range top and all was fine.

Parts Used:

Surface Burner Spark Electrode

Robert from Irvine, KY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No Spin Cycle

Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.

Parts Used:

Screws - Package of 12

Richard from LORDSBURG, NM
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

One burner would not ignite.

I replaced the igniter under the knob.

Parts Used:

Gas Valve Switch

Eve and from MIDLAND, MI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom Heating element quit working after 30 years

Removed several screws and removed element. Replaced same. Total ten minutes.

Parts Used:

Screws - Package of 12

Harry from Dills burg, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Sparking at 2 different burners all by themselves

Replaced Spark Module and adjusted igniters

Parts Used:

Spark Module - (4+0)

paul from las vegas, NV
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Will not ignite

Shut of electric supply. Remove knobs and open top cover of cook top by removing two screws near each burner and replace switch.

Parts Used:

Gas Valve Switch

pradyuman from Parlin, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner would not ignite

The top is all glass so I took my time. There was about 12 screws and double sided tape. A lock washer holding the igniter on. It also gave me a chance to clean the hard to get to places. Your price was almost half of what a suppier here and getting it would have been 2 weeks compared to your 48 hours to my door. Thanks again

Parts Used:

Gas Valve Switch

Kenneth from Brooklyn, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

would not ignite

It was so easy.I removed the old part with the new with pliers. Voila/// it worked.

Parts Used:

Surface Burner Spark Electrode

Terry from Longmont, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The spark module would constantly spark

I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.

Parts Used:

Spark Module - (4+0)