JGD8130ADW Jenn-Air Cooktop - Instructions

Turn off power, removed wires from switch, unscrewd lock nuts. Did the reverse to put the new switch with the exception of the the power which should always be turned off first. Took less than 5 min. to install. Wife happy!! which makes me happy.

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.

Extremely easy.
First, I turned powr off to appliance at electric panel (don't trust switches).
Next, I removed the 2 screws that held the panel cover, removed the dials, and removed 2 screws at each one (total eight) - this requrid a hex screw driver bit, which I had in my handy set.
I proceeded to loosen the panel, and disconnect the wires attached to the old switch (this may be tricky - mine came off easy, but did require care as to not to strip the wire from the clamp).
Once the old switch was removed and the plastic housing unscrewed, I attached the new fan assembly, and connected the wires, and reinstalled everything back in the same order.
(This is a good time to clean all the grease and dirt that has collected thru the years-before you put everything back).
Turned the power back on, and everything worked like before.
I figured I saved about 4 hours worth of labor (4x$50=$200 / minimum) plus any inflated part price I would have paid for a $20 part from PartSelect! It felt good!

Watched u tube video as supplied and followed instructions. Had trouble getting burners off so cleaned around edge of burners with fine bladed knife as suggested by other forum user and used oil filter type wrench to remove burner. There are three bumps on burner that hold it in place so need to turn anti clockwise to remove.

Turn off the gas supply and unplug the electric supply. Remove the top grates and the burner cartridges. Remove 12 screws around the top cover and loosen the two screws for the fan switch. Pull the fan switch up and out of the way, remove the top cover. With a marking pen, label the four igniter switches and pull them off the gas valves. From underneath, remove the gas line from the pressure regulator, then remove the regulator from the pipe coming from the circular manifold. With a 3/16 socket (1/4 inch drive) or a 3/16 nut driver, remove the four screws that hold the manifold. Then from the top pull the manifold up and out. On the bottom, remove the screw (1/4 inch socket or nut driver) and remove the old gas valve. That's it. Now just put it all back together in reverse order. I used pipe joint compound on the pipe threads. Check for leaks with a soapy water solution. If I had to do this again, it would only take me half the time. I wasn't sure how everything came apart the first time..

This cartridge fits my JennAir Downdraft Slide In Rage, part No. JDS9865BDP. The burner cartridge replaces a downdraft cooking grill module that comes with the original stove/Oven.
The spark quit on the cartridge side. I re-inserted the original cooking grill, and it lit fine. There are two components to look at. The sparker, and the burner igniter (one per each burner). Since both failed to light, I ordered the spark controller.
PartSelect has a video on how to test for failure, but I couldn't find that again.
Two screws mount the controller, two wires re-connected. and works perfect.

Put the new pad in and it was done. Very easy.

Two screws inside the exhaust box to take out the switch assembly and 2 nuts on the switch. Nothing to it

Remove switch cover with two screws ,remove two nuts holding switch in place ,remove switch,then reverse procedure with new switch.

Flip the breaker. Lift off the fan center grate. Remove two screws located on back of the burner dials housing. Lift the back of the housing, then pull this gently away from the front to unhook the front. Turn this over, locate the switch. Pull the three electrical plug connections from the switch plastic housing, remembering their locations. Back off the two nuts holding the switch to the underneath side of the dials housing. Place the new one in place, put it all back together.

remove two nuts and install new switch, then change wire connections from the old switch to the new one.
Then place it back together.

Prepare a flat area with newspaper, a screwdriver, and a small bowl for the screws, and a small wire brush (if you want to clean as you go). I also recommend taking photos as you proceed, for reference.

ALSO, take close note of the orientation of the cook top base, one end has a lip that's allows for burner assembly removal.

Remove entire two burner assembly, place upside down on newspaper, remove seven Phillips screws, remove assembly bottom.

Remove small screws from gas tubes, pay close attention as you remove the gas tube from the bottom of the burner, to the orientation of the two washers (the washers have an edge).

Remove the burner tubes and washers.

Carefully remove the igniter connectors from igniter.

Remove the end of the assembly.

Grasp the burners, and turn to rotate the burner to a position where the "bumps" on the burner match up with the gaps in the burner cook base. Remove the burners.

The old burner base can be set to the side. At this time i cleaned the burners throughly with a small toothbrush size wire brush.

Assemble the burners to the new top base by aligning the bumps to the opening in the cook top base, turn slightly to keep burner in place. Insert the gas tubes, with the washers (be careful about the washer lip orientation) with the smaller screws, do not overtighten!

Attach the igniter connector to the igniters.

Align the burner/gas tubes with the assembly end. Carefully set the base into place, adjust the tubes as necessary to get the screws aligned with the holes. Install the screws, tighten hand tight.

Install entire assembly into cook top, check igniter and burner operation.

Glass cleaner is great for cleaning the new porcelain surface.

Disassembled old part put new one in reversed order

took out burner and remove ignite r and reinstall a new one simple as that

First I did was to google the problem I have. There several video how to solve the problem. It show me different ways to solve my problem. I just follow the instructions. Thank to google without it, I am lost. I may add, that google is a big saver for me.