Models > JGA8100ADB > Instructions

JGA8100ADB Jenn-Air Refrigerator - Instructions

All installation instructions for JGA8100ADB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JGA8100ADB
16-30 of 30
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burner heads were rusting through and letting flame leak out

  • Customer: Steve from Townshend VT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Lots of small metal screws to remove on the housing, gas supply and electric igniters. The only challenge for me was getting the old burner heads out of the trays- they ere rusted up and needed a little penetrating oil and time to break free. I re-used my old igniters- had to bend open the little metal rod at the tip a half of a millimeter to get them to fit back thru the new heads. Keep track of how things come apart and the way the gas lines assemble and it's an easy project. Be careful not to over-tighten old screws in rusty holes in the trays.

Burner igniter was not lighting the pilot. Needed replacement.

  • Customer: Arthur from South Burlington VT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.

The old burner was rusted through and the gas port came loose from it.

  • Customer: Roger from Syracuse IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
To gain access to the burner, the bottom of the double burner unit had to be removed (7 screws). Once this was achieved, it was a simple matter of removing the old burner head which is captured with three lobes that engage the unit much like a thread,(which in my case was stuck in because of rust and had to be persuaded with a pipe wrench). The new burner was installed with hand pressure only, and once the gas flange was remounted and the ignitor hooked up, I just re-attached the bottom of the unit and viola!

Wore out burner and igniter

  • Customer: Bruce from Vashon WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
New burner and igniter.....actually it was very easy to to fix

Replacement of top burner igniter

  • Customer: Godfrey from Las Cruces NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Twisted and lifted off the burner, loosened in a previous repair; removed electrical wires from igniter; undid two screws holding igniter in place; rotated igniter 90 degrees and lifted it out; reversed process with new igniter.3

Gas burner would not light-had to use lighter

  • Customer: James from Osage Beach MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
As described for the part. Easy repair. Easy to diagnose thanks to feedback from another customer of yours. Part was received super fast.

BURNER IGNITER AND BURNER

  • Customer: ROBERT from MADISON FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
DIS MANTEL BURNER UNIT REMOVED BURNER REPLACED BURNER AND IGNITER

Igniter not working

  • Customer: Casey from Soledad CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed old igniter. Porcelain was broken. Replaced with new igniters. Really simple to do. Took 10 minutes to replace all 4

2 burners rusted apart, 1 gas valve frozen up.

  • Customer: robin from saint marys GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed burner pan screws,igniters, gas tubes & burners. Changed 2 igniters, removed rust & repainted ends of 2 of the tubes (heatproof paint). New burners were made a hair smaller than original but locked in O.K...Now, the hard part...disconnected all four tubes from gas valve assembly. (Had to shut off gas to house in order to remove main gas line to stovetop.) Had to remove valve box in order to remove/replace frozen valve. Unit is 25 years old, works as and looks new...Rust was caused by boil-overs.

Broke the insulator on the ignitor while cleaning the cooktop.

  • Customer: David from Shelley ID
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.

gas burner had rusted out

  • Customer: John from Nashville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced burner

Burner head was rusted through

  • Customer: Joellen from Castro Valley CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This is the second burner head I have replaced. It was easier than the first time but the burner head I received did not have the screw holes to reattach the gas tube to the burner head. I was able to drill my own without too much trouble using a standard bit and electric drill. I used the old burner head to determine what size drill bit to use. Even so, it was still an easy fix.

burner head rusted out

  • Customer: jon from bartlett TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
undid about 7 screws to get access to underside of burner, unscrewed 4 screws that held on gas feed pipe and ignitor. twisted out old burner and gently removed ignitor from burner. cleanded up area where burner was and installed new one. took a little bit of tweeking to reinsert ignitor but did slide in nicely. reattached gas pipe and all screws. slide burner case back into position. turned on and worked nicely.

Broken Burner Head,

  • Customer: Harry from Brookeville MD
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Take your time and remove items carefully and replace with new items. Very easy but you definately cant rush and possibly need new screws to make it even easier.

The igniter on my stove wouldn't ignite.

  • Customer: keith from massillon OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched a video on replacing igniter. Removed old igniter and replaced it with new igniter.
All Instructions for the JGA8100ADB
16-30 of 30