JFC2087HRP Jenn-Air Refrigerator - Instructions

Followed the video, 5 minutes later new piece installed. Unfortunately, the new plastic is like the old and the same defect could easily recur. thanks

I ordered the replacement parts on line and received it a few days later. Thought I'd wait till the weekend to install the new parts. I expected it to take longer so I waited. Boy was I wrong. The hardest part was unloading the top shelf of the freezer. And it took longer to go get the nutdriver. I should have put it in immediately. Thanks for the instructional video. Works like a dream NO LEAKS. Will use your services on other parts as needed. Don from Pittsubrgh, PA.

Followed video advice

Removed malfunctioning icemaker and discovered that inlet water line was frozen. Thawed line using hairdryer and problem resolved. Returned new icemaker to PartSelect they promptly credited my credit card account. Problem solved.

I discovered that the water inlet was freezing, then the incoming water would run into the tray. I watched the video, then removed the ice maker. I discovered the the top two screwed just had to be loosened, not removed. I removed the bottom screw and move the ice maker to the side to disconnect the wiring harness. I found it to hard to disconnect. The pinch clips did not depress as they were supposed to, but the finally release. I did the replace without unplugging the refrigerator and it went fine. Took less than 15 minutes.

I removed and inspected the old unit and found the tray coating was flaking off. I ordered the new ice maker on line, One screw and rotate unit counter clockwise about 10 degrees unlocked it from the two snap in mounts. then unplugged the wire harness and it was free. Had to put the short wire harness on new unit, reverse removal steps and it is completed and working fine.

I watched your "silent video". I am a 62 year old woman that is very hands on when it comes to tools and power tools. It was very easy.

Move refrigerated and turn off water and unplug elect. Remove ice Ben and guide on right side. Move one screw on the bottom and lousen tow screws on top. Remove ice maker to unhook electrical connection. Transfer parts from old one to the new one . Revise the removal of it and when done .Plug in cord and turn on water. If you have done everything very carefully you will have ice in a few hours.Good luck.

Replaced the ice maker. I have a 3 door refrig. It has a bottom drawer freezer. Remove the freezer door to make this much simpler. On my unit, the ice maker is installed with three screws, rather than one and two clips. Check before you try to pull it out. You should unplug the old ice maker from the refrig, leaving the wires on the old ice maker. It's much easier to remove the old wiring harness from the old ice maker once you've removed the front plastic cover on the unit. Both plugs on the harness have clips on them to prevent accidental disconnections. Be sure to find and press the clip releases before you pull on the wires. Nut driver makes this job easier than screw driver. You only need one size for all screws. I used the old ice maker bottom mounting clip rather than trying to bend the new one to shape. Much easier. My old ice maker had an extra wiring clip, which I moved to the new unit before the install. There is one wiring clip to hold the temperature probe, and another just to keep the wires neat. Letting the old ice maker front plastic cover warm up a bit before you try to pry it off for reuse is a good idea. Less chance of cracking. Two hours after the install, I had new ice in the ice bin.

Opened the refrigerator door, pulled down the filter cover, twisted the old one out and removed it. Placed the new one in - twisted it into place, replaced the cover and closed the door. It is working great!!

Open box put shelf in

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

I fortunately found the Part Select web site!! Used the trouble shooting guides and diagrams to diagnose the likely problem. Viewed the installation videos provided on the site and followed the procedure to complete the repair in about 15 minutes. It was a snap (actually three snaps) Fridge now working like new!! Thanks for the great information, guidance, pricing and superfast delivery!! Ron

Excellent easy to follow video. Had expected a hassle but whole repair was very smooth and everything worked as shown in video. Sure beats impossible to follow drawings. My wife was amazed I could do it...usually I can't fix anything!

Thought I needed a new filter. Did not solve the problem. I returned the filter to partselect as per instructions. Will order from partselect when I need parts.