JEW8627AAW Jenn-Air Wall Oven - Instructions

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

The door came off easily after I removed the two hinge covers that are attached to the oven. Taking the door off can be done with one person but ideally two.

The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).

After that, re-assemble the door and drop in place. It was a snap.

FYI...the shipping was ultra fast and the price was great.

No issues whatsover with the entire process.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

First I opened the door to the oven so that when I turned off the circuit breaker I got the right one. I then removed the four screws holding the panel on, disconnected the wires, removed the screws holding the assembly in place, put in the new assembly in place, put the screws back in, re-attached the wires, and screwed the panel back on, ran down and hit the circuit breaker, and voila' we have light.

Removed 4 screws thathold the diplay panel on, unplugged three electrical connectors and removed for screws holding the display on. Easy!

removed the four philips screw on the oen cover plate. slid the plate off and disconnected the serial wires. removed the four 1/4 hex nuts holding the control panel on. replaced with the new control panel and replaced the four screw nuts. re-assembled the serial wires, placed the coveer plate and replaced the four set screws. that easy.

Removed a couple of screws and removed display panel. Replaced clock display on back of the panel- was held on by two small hex head screws -1/4" nut driver and phillips screw driver were the only tools required, very easy repair that
the appliance repair man wanted 750$ to do.

Removed front panel form oven front ( in the wall double oven), disconected 3 wires, removed old clock assembly (4 screws), replaced clock assembly, reattached 3 wires, reinstalled front panel (4 screws). Done!

removed panel, removed clock and installed new clock, reinstalled panel

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

(turn off the breaker to the oven.)take the eight screws that hold the oven in the wall out. then cut a piece of wood about 3/4" square 29 3/4" long to hold the oven out away from the wall while changing the control panel. there is four screws below the control panel to remove. lift the panel towards you and raise it up . disconnect the wires carefully. set the panel on a counter and remove the four screws that hold it in place. change the control board and reverse the process. turn the breaker back on and you are done. very simple job,

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

7 minutes to turn off the breaker - unscrew the old element, pull out the old element attach the new element and rescrew. 10 minutes to replace the broken bulb since the base was left without the glass bulb to turn.

Parts no longer available so we went to several appliance stores and measured racks. We found a jenair model had racks that measured correctly got the model number and ordered the racks. There working great and now the oven looks like new. Our kitchen is a restored 1956 GE metal kitchen in Cadilac pink. Thanks guys for the fast service and very resonsble price. Was also very happy to find the racks were made in USA.