JDR8895AAS Range - Instructions

The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.

unscrue 2 scroos remouved from the soccets and poot the new one

Extremely easy replacement. Followed the instructions and suggestions from previous users which was emphasized about turning off electricity. Main difficulty was that we are not young people, had to reach on knees and stretch to back of oven. Put hot pads under knees for comfort !!!!!!

Parts package contained no instructions. Found all instructions on internet. I used Phillips head to remove two screws on anchor plate of Long Oven Sensor. Located at upper left, back corner of oven; access to screws is not simple/easy. Screws back out w/o difficulty. Pull/extract sensor harness through hole[back of oven] which required pushing aside insulation. The harness barely fits thru hole in oven back metal wall; I recommend using needle nose pliers ( which I ended up doing ) for ease of extraction. Disconnect harness plastic interlok clips. Perfect reconnection of new clip harness with ease. Reverse procedure to complete installation/repair. Done in just over 35 minutes due to wrestling with harness extraction through minimal hole opening. Failure occurred on Thanksgiving Day with 22lbs turkey in oven. Top of turkey contacted sensor tip which eventually caused sensor fault; result was scorched upper breast and oven shut down [safety by design]. Cook top was still operative; clock and all readings on digital control panel ceased. With new 'long oven sensor' installed - good as new. Will be sure to buy turkey(s) under 20lbs in future. Jim in Seattle

Removed the back of the stove, un-pluged the sensor wires, removed the sensor from inside the oven. installed the new sensor, pluged in the wires, and replaced the back of the stove. A phillips screwdriver was the only tool needed.

I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fish out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.

My wife came to me distraught one day and notified me that the upper broiler element in our oven had caught fire and melted into pieces. Like I really needed one more thing on my "honey do-list".... I thought about just replacing the entire oven, but even at 10 years of age, it looked great and had performed like a champ up until then. After a little research on the web (you tube videos and such) and your easy to follow partselect.com site, I ordered a replacement part at a very reasonable price. The replacement part arrived within a couple of days. A screwdriver, flashlight, and fifteen minutes later...WALAAA!!! My wife was full of praise and appreciation before making me my favorite dish in the oven that night!! Thank you Partselect.....

I lifted the burner tray from stove turned it upside down then removed six small screws from side of cover pan then I removed the cover then I removed the screws from the back of the old burners and igniter.Then I turned the old burner counter clockwise and it lifted out easly. the igniter is removed with no problem. The new burner is put in place and turned clockwise to lock in place.Then replace then the gas tubes and igniter and igniter wire then put tray cover on.

very easy. a few screws and the wires just hsave push on terminals. Of course it goes without saying, unplug it first!

I took off the backing plate to the oven and changed the element out. I realized after I did the repair there was a smaller removable plate at the bottom to change the element. This would have saved me a lot of time, but the whole repair still took less than 30 minutes and everything is working fine.

Ordered the element, it took a little longer to come in than I expected, but it was over Christmas. My grandson and husband took the old one out and put the new one in in less than 5 minutes. Wonderful!!

I can't believe my husband put this in without cussing. It took him only 15 minutes. WOW!

Replace the oven sensor per the excelent easy video you provided

While doing a clean cycle the lower element got really hot in one area and then burned thru. I let cool, removed racks. I found that two screws held element in. Removed screws pulled element out unfastened push/pull wires. Ordered new element reversed removal... Works Fantastic. Entire job took less than 10 min. By the way. I ordered the new element around 3PM. I was BLOWN AWAY when it arrived the next day!!!! Truly Impressed!!! THANKS

Watching the video of how to replace the sensor was great help and much appreciated, the only difference was that my wires were much shorter and I had to pull the oven out of the cabinet to get to the back of the oven to release the clip holding the wires together, unlike the video where the man jiggled the wires until the clip holding the wires together came through the little slot where the probe is attached, otherwise it was pretty simple, just a few extra steps to pull the oven forward to get to the rear to release the clip holding the wires together. Once I was able to release the clip I used one of the 2 adapters that was sent with the sensor probe and attached them after putting the wires through the hole where the probe was attached first then replaced the 2 screws that holds the sensor in place, slid the oven back in and turned the circuit breaker back on and it works perfectly. The video gave me the confidence to do this job though and I thank PartSelect very much for being a great company to help with videos and sending the parts so quickly.