Models > JDR8895AAS > Instructions

JDR8895AAS Jenn-Air Range - Instructions

All installation instructions for JDR8895AAS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDR8895AAS
271-285 of 285
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replace lower bake element

  • Customer: Charles from Ripley MS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove two screws at back of oven. Pull the element out, remove the electrical slide connectors. If the electrical wires fall back through the openings, pull the range out from the wall to access the back..remove the small cover panel at the lower left and you will have full access to the connectors. Put the new element in place, connect the electrical connectors and replace the securing screws. Replace the back cover panel if you removed it. Job finished.

burnt heating element

  • Customer: Bobby from Elizabethtown KY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
turned power off to oven removed screws that held heater, installed new, very simple

spontaneous fiery rupture of element

  • Customer: cindy from boonville MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After disconnecting the power... I removed the lower racks for clear access to the back of the oven. I used an electric screwdriver to remove the two small screws and then gently pulled the element away from the oven, exposing the connections. Using two pairs of pliers, the connections were separated and the element removed. Installing the new element was simply a reversal of these steps. My biggest concern was that I might break the oven door as I lay on it.

Both elements burned out after considerable use.

  • Customer: Iron Leaf Forge, from La Grange KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This is an instructable for Maytag Range No. JDR8895AAS.
Tools: #2 Phillips head screw driver
Time: Less than 30 minutes total.
Replacement of:
Top Oven Broiler Element (Schematic Item #10 Part Number: PS2342087) and
Bottom Oven Bake element (Schematic Item #2 Part Number: PS2362492).

Item #10:
1. Oven and Stove must be cool and POWER MUST BE OFF TO RANGE. Carefully pull range to access the electrical
plug. Unplug range from electrical outlet. Replacement is done from INSIDE of oven.
2. Open the oven door to the first stop (about 1/4 open). Pull the door straight up and off the hidden hinges.
3. Using a #2 Phillips head screwdriver- From inside the oven, remove the single screw located just below where
each element enters the back (inside) of the oven. (2 screws total) Note the position/orientation of the screw
plates.
4. The element is supported by an "L" shaped slotted bracket. Note the position/orientation of the bracket and
remove the two screws located on each side.
5. The element's prongs project into the back of the oven and have a bit of an angle to their connectors so some
manipulation is required to get them out of their holes. Gently guide the elements out so the connectors and a
few inches of wire are through the holes.
6. Firmly grasp the connector and the element prong and pull apart to disconnect. As the connectors are angled it
is helpful to view them with a flashlight to determine direction of pull.

7. Replace- To replace the element simply reverse steps. Note: Screw plates down and "L" bracket with 'screw
plate facing door.

Item #2:
1. Oven and Stove must be cool and POWER MUST BE OFF TO RANGE. Carefully pull range to access the electrical
plug. Unplug range from electrical outlet. Replacement is done from INSIDE of oven.
2. Open the oven door to the first stop (about 1/4 open).
CAUTION: THIS DOOR IS CONSIDERABLY HEAVIER THAN THE TOP OVEN DOOR.
Pull the door straight up and off the hidden hinges.
3. Using a #2 Phillips head screwdriver- From inside the oven, remove the 2 screws located above the element
where it enters the back of the oven. This element does not have a bracket.
4. The connectors and prongs are straighter so gently pull them and a few inches of wire into the oven area.
5. Firmly grasp the connector and the element prong and pull apart to disconnect.

6. Replace- To replace the element simply reverse steps. There are no position/orientation issues.

Inside glass had shattered after doing self cleaning.

  • Customer: Kim from Shrewsbury MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Called a repairman who installed the piece of glass as the old piece was difficult to remove. Started project so I could clean the various glass pieces but was happy he came and finished the job. It took him over 30 minutes and like I said I had most of the door apart.

WHEN WE TURNED ON THE OVEN THE TEMP. READING WENT UP TO 425 AND BEEPED BY NO HEAT

  • Customer: DAVID from Cape Coral FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back WOW saved me $500. from buying new and $150. for service call

The lower element burned through I'm one small area. it was glowing like a lightbulb before it opened up.

  • Customer: Mark from Carthage MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I first pulled power from the unit. In the lower oven I removed two screws on the lower bake element shield and pulled it out until the spade connectors were exposed. I disconnected the spade connectors and installed the new element and replaced the retaining screws.

change oven sensor

  • Customer: Lloyd from Eau Claire WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed provided video

The inner glass shattered when the oven was in the clean mode

  • Customer: Charles from Sulphur LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First I took the door off and outside to dump the glass in the trash which I had some Kevlar gloves so not to get cut. Removed the three screws on the bottom trim piece and the two on the sides remove the outside face glass next remove the four screws that hold the next glass. This glass is in a frame there is bent tab on one corner unbend open frame and install inner glass close frame rebend tab and reinstall all the parts.

Maytag range had "F3" code display, oven would not work.

  • Customer: phillip from Farmington NM
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.

gasket needed replacement on exterior oven door

  • Customer: frederick from feura bush NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
first the part was ordered but found it way too overpriced. went to an automotive store and bought door edge molding for a lot less. and it was better quality that the original gasket. with the self stick interior of the door edge molding was a fast and simple repair and more secure.

Oven would not heat on Back Cycle

  • Customer: Jeff from Thousand Oaks CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Burned Lower Bake Element

  • Customer: Thomas from Thomaston GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws on the existing element bracket plate. Pulled element out a few inches, unplugged existing element, re-plugged new element , pushed back in and reattached element bracket plate with the two screws i removed. Very very simple

Burned out lower oven bake element

  • Customer: Karl from Ballston Lake NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. I shut off the power to the range; 2. removed the racks from the oven; 3. removed the two screws that secured the old element's mounting flange to the back of the oven; 3. pulled the old element out; 4. disconnected the two spade lugs from the old element; 5. reconnected the spade lugs to the new element; 6. remounted the new element to the back wall of the oven; 7. fastened the element flange with the two screws (from step 3.) 8. replaced the oven racks; 9. turned the power to the range back on; 10. verified the oven's functionality -- 15 minutes, tops!

upper broiler element in top oven failed

  • Customer: scott from Chandler AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
super simple - I took the back of the oven off to get to the push on connectors - the connectors were on tight but I could get them off by hand... remove the 2 phillips screws at the back of the oven (used a long phillips to get to them easier.) then remove 2 phillips head screws holding the element up with a short screwdriver and swap the elements out. Reverse the process and you're done...
All Instructions for the JDR8895AAS
271-285 of 285