Models > JDR8895AAS > Instructions

JDR8895AAS Jenn-Air Range - Instructions

All installation instructions for JDR8895AAS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDR8895AAS
256-270 of 300
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The lower element burned through I'm one small area. it was glowing like a lightbulb before it opened up.

  • Customer: Mark from Carthage MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I first pulled power from the unit. In the lower oven I removed two screws on the lower bake element shield and pulled it out until the spade connectors were exposed. I disconnected the spade connectors and installed the new element and replaced the retaining screws.

change oven sensor

  • Customer: Lloyd from Eau Claire WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed provided video

The inner glass shattered when the oven was in the clean mode

  • Customer: Charles from Sulphur LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First I took the door off and outside to dump the glass in the trash which I had some Kevlar gloves so not to get cut. Removed the three screws on the bottom trim piece and the two on the sides remove the outside face glass next remove the four screws that hold the next glass. This glass is in a frame there is bent tab on one corner unbend open frame and install inner glass close frame rebend tab and reinstall all the parts.

Maytag range had "F3" code display, oven would not work.

  • Customer: phillip from Farmington NM
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.

gasket needed replacement on exterior oven door

  • Customer: frederick from feura bush NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
first the part was ordered but found it way too overpriced. went to an automotive store and bought door edge molding for a lot less. and it was better quality that the original gasket. with the self stick interior of the door edge molding was a fast and simple repair and more secure.

Oven would not heat on Back Cycle

  • Customer: Jeff from Thousand Oaks CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Burned Lower Bake Element

  • Customer: Thomas from Thomaston GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws on the existing element bracket plate. Pulled element out a few inches, unplugged existing element, re-plugged new element , pushed back in and reattached element bracket plate with the two screws i removed. Very very simple

Burned out lower oven bake element

  • Customer: Karl from Ballston Lake NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. I shut off the power to the range; 2. removed the racks from the oven; 3. removed the two screws that secured the old element's mounting flange to the back of the oven; 3. pulled the old element out; 4. disconnected the two spade lugs from the old element; 5. reconnected the spade lugs to the new element; 6. remounted the new element to the back wall of the oven; 7. fastened the element flange with the two screws (from step 3.) 8. replaced the oven racks; 9. turned the power to the range back on; 10. verified the oven's functionality -- 15 minutes, tops!

upper broiler element in top oven failed

  • Customer: scott from Chandler AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
super simple - I took the back of the oven off to get to the push on connectors - the connectors were on tight but I could get them off by hand... remove the 2 phillips screws at the back of the oven (used a long phillips to get to them easier.) then remove 2 phillips head screws holding the element up with a short screwdriver and swap the elements out. Reverse the process and you're done...

Lower element stoped working.

  • Customer: Jennifer from Shirley Mills ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws, unplugged two wires removed element. Installed new element, hooked two wires up and put two screws back in.

Lower Oven Bake element burned out and snapped two places

  • Customer: Howard from Hermitage TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My dearest wife could not wait for me to get home from work. She wanted to bake some special cakes. She removed the screws that mounts the bake element to the oven wall and removed the old element. Just used a screwdriver. However one of the mounting screws tumbled out, behind the oven wall through the element opening. She retrieved the screw with pliers, plugged in the replacement bake element, replaced the screws, and baked her cakes. I came home to a freshly baked-cake aroma in the house. What a gal!

Lower Bake Element Broke

  • Customer: Chris from Lees Summit MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I took the two screws off the inside wall oven that attached the lower bake element. I then removed the two screws on the face plate on the back of the oven to allow access to the lower bake element and the wires. I removed the wires from the bake element. The bake element clips slip off, you can cut the element clip/don't cut the wire clips you will need them to attach the new element. Remove the old element from inside the oven and insert the new one and reattach the clips and rescrew all the screws and get cooking. A flashlight may be needed inside the oven.

Oven only heats to 250F regardless of temperature setting. Identified pitting in one location on the element.

  • Customer: Chris from Arlington TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove racks from oven. With a #1 Philips head screwdriver, remove the two screws holding the element in place against the rear wall of the oven. Gently pull the element forward, taking care to NOT allow the electrical connections to slip off the element's tabs. Remove the two wires that supply power to the element. Connect the two electrical wires to the new element. Place the element in place and start one of the two screws that hold the element in place against the rear wall. Start the second screw and tighten completely. Tighten the remaining screw. Test the heating element to 450F to verify proper operation.

Broiler element was not heating

  • Customer: Thomas from Clinton CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pull the range out from the wall and unplug it. Open oven door and remove philips screws holding the element in place (in back of oven). Remove the back cover removing philips screws holding it on. Find the wires connected to element (element is now loose) and remove wires (pull off). Go back to the inside of the oven and remove two philips screws holding the bracket on the top inside of the oven that is holding the heating element. When I removed these screws I found that I was not able to reinstall the screws due to metal fatigue. I had to cut two pieces of metal, drill small holes in them, remove the two screws holding the stove top (at the front of the range) in place. I then pulled the stove top forward and up. I had to cut two small holes in the insulation to find where the screw holes were. Then I reassembled the bracket and heating element put the screws one at a time up through the holes in the top inside of the oven, lined up the metal pieces that I had cut and tightened the screws. If I had not had to do this it would have been a 10 minute job. Then you just reinstall the screws in the back of the oven that hold the heating element to the back of the oven. Reconnect the wires in the back and reinstall the back plate of the stove. Plug in the range and all is better.

Range had an F-2 code on the control panel

  • Customer: Greg from Frederick MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou
All Instructions for the JDR8895AAS
256-270 of 300