JDB3610AWX Jenn-Air Dishwasher - Instructions

Just put it in the dishwaser. Worked & looked great. Simple job.

replaced broken part

Replace parts for Impeller and Seal Assembly. Most things came off reasonably, but the final Impeller would not and had to be forced out in pieces. Probably because of this after putting new parts in place the leak was worse than before.

before ordering parts i noticed lower right side of door gasket was missing about 1 inch. when ordering door gasket i thought for the low cost of latch grommet i should order that also....glad i did. pulled out old door gasket, cleaned where new gasket would go and replaced it. tried the washer and when it reached the main wash the leak started again. took the 7 screws out of door removed 2 nuts and replaced the dispenser door latch grommet.....problem solved. dont think because the old grommet looks fine that is not bad. im not a "repair kind of guy " but this was easy and toof 20 min.

removed the inner door panel. replaced the wax motor. that's all it took.

My dishwasher has always done a fanastic job of cleaning, even dried on food without rinsing. Now it began leaving stains in the cups and the door to the machine was staining too. I was sure the whole thing would need to be replaced. My 'fix-it' husband found your internet site with a little better price on the little motor part needed and it came in just a couple days. The actual cleaning and scrubbing of the dishwasher's surfaces probably took longer than installing the part. It seems to be working great right now, and it's still 18 years old! Thanks, Carole

Removed lower rack and after assembly of tower spray to new rack, put new rack in dishwasher.

First I slid out the old rack, twisted the spray tower off of it and on to the new one, and slid the new rack in. No tools needed.

It was very simple,took out the middle water dispencer replaced it and filled the dishwasher . and for got about it. The lady was very helpfull and could under stand her.thanks vern

Thanks for the instructions. It helped. However, there should be more attention spent with the seal at each end. On one side it is evident that the seal should be flush to the bottom of the door. However, the right side seems to indicate that the excess seal should be left hanging out. That is what I did the previous time I replaced the seal. Soon it started leaking. This time I made both sides of the seal flush with the bottom of the door. Also the first time I installed the seal, it was too short. I had to reset and slightly pull the seal to increase length.

Repair was simple, and easy to install. Instructions were fairly straight forward. Only thing to be aware of is when you get to the last part, the cutter blade, it is difficult to remove, and you must pay attention to get it on the new impeller fully seated and make sure that the tabs clear the upper cover that goes on top of it. I had an issue with the tabs catching, causing a loud noise, I simply removed, rechecked, and cut the tabs down a little bit, and re-installed. Overall, took me an hour to complete and I have a quiet and functional dishwasher again!

I had to make several attempts as follows:1.I replaced the door gasket, still leaked, 2.Replaced the float and micro-switch, still leaked.3.Replaced the insulation inside the door., still leaked. 4. Finally,read your diagnosis info and ordered the gromet. It was delivered in under 24 hours to my Island home!5.Took off the 7 door screws, unscrewed 2 screws that held the latch mechanism, replaced the rotted gromet and Voila! no leak. Once I found the problem, it took 15 minutes

There were no instructions with the rubber gasket seal . The gasket kept popping off. Finally got it to stay and it still leaked. We actually siliconed it in.

Roller broke on RH side of upper dishwasher rack. No roller replacement kits for this part were available. I purchased a roller for another model dishwasher. This roller came with a bracket that wasn't compatible with my dishwasher. I modified the bracket by cutting it with a utility knife. I also had to trim the hub of the roller about 1/4" I then used a 10-32 hex head screw and locknut and mounted the roller and trimmed bracket to the bracket on the dishwasher rack. Knowing what I have to do - the next time I do this it should take about 15 minutes.

Took out existing water inlet valve and installed new.