JCD2295KES Jenn-Air Refrigerator - Instructions

I went on line and viewed the video. It looked so easy I ordered the new ice maker. Having the information I was able to take apart the old one and view the problem. By the time the new part arrived I was experienced with the installation. I was shocked when the new ice maker arrived within 1 day. I completed the installation without a hitch, I was delighted with the ease of installation and the operation of the new iace maker.Thanks again...Ray

went by instructions, used a little common sence.

I removed contents of freezer as this was a bottom unit. I had to remove freezer drawers/door to easily access ice maker which was located in the back of unit,wasnt a problem.I did however take a hair dryer to water tube as it froze up with about an 6 inch tube of ice that finally slid down. Connected unit and had ice within an hour or so and a full tray within 24 hrs. Second ice maker in little over a year...Video very helpful, saved 100 bucks by doing myself. Part arrived fast, great job!

We ordered a PartSelect PS2121513 ice maker. I was concerned that there was no instructions shipped with the unit. Fortunately, PartSelect had an online video that guided me through the process. It wasn't that complex really. The only time I felt totally dumb was when using my nut driver to remove the bottom bracket. I couldn't figure out why there was no 1/4" socket with my set, so I used a small socket wrench instead. I finally figured out that the driver was already a 1/4", without a socket in it. After that it was easy. Slid the ice maker up a little to free it from the top mounting screws. Pulled it outward a bit to gain access to the connector at the back of the freezer, then squeezed the two sides of the connector and out it came. I popped the plastic cover off the existing device and then removed the connector as instructed in the video. I also removed the bale (as per the video). I put the connector harness, plastic cover and bale on the new ice maker and put it back in, this time using the nut driver on the bottom bracket :-). My only concern after that was that it didn't seem to be working. I had no idea that it needed some time to get cold before it would work. After about an hour, it filled with water and began making ice. Success.

Removed bucket,and removed the front cover. the ice wheel was removed by removing the nut from the blade assembly and removing the blades washers and spacers. The parts were replaced in reverse order and the nut replaced. The ice maker was removed by removing the bottom bolt, loosening the two side bolts and lifting the unit off the bolts. the cover was removed from the ice maker and the tab depressed on the wiring harness which was then unplugged. The wire was removed and replaced on the new unit the harness plugged into the new unit and cover replaced. The unit was the placed back on the bolts, tightened and the bottom bolt replaced. the ice bucket was replaced and unit turned on. Ice making within an hour.

turned off the water supply,disconnected the power from icemaker to the back wall,loosened the two screws on the top,and one screw on the bottom.removed old icemaker.took the bale off,to put on the new icemaker.removed the wire harness from the old,to put on the new icemaker..saved over $200 for the repairman,had a full tray of ice in 6 hours.(watching the video,helped)!!!!!,very thankful for your service,as most of my appliances are all in that ten year period,i will be ordering more as needed.

Empty out freezer loosen two top screws and took out bottom screw. Lifted out ice maker and unplugged wire. Took bailing arm and plug and put on new ice maker and reverse the process. Had ice in three hours and no leaks.

The repair was simple. It was a matter of unpluging the old relay and then pluging in the new one. I almost bought a new refrigerator but after doing alittle reading on this web sight and finding out the most common reason for having the problem I was having I decided to order the relay. It was the problem...$ 70.00 -v- $1400.00. I'm HAPPY !

Removed wiring from old ice maker and install on new. With 2 screws all ready in place hung ice maker on them. Attach wire connector into socket and install bottom screw to hold ice maker. Tighten top 2 screw and put wire guide in place. Drop wire guide down and ice started in 10 mins

Rmoval and replacement is not at all complicated. (1)Reach behind and to the left of the icemaker and release the power plug. There is a release snap on th side of the plug. (2)Using a 1/4" nut driver remove the screw holding the icemaker to the "L" bracket at the bottom of the icemaker. (3)Using the nut driver loosen two self taping screws holding the top of the icemaker to the side of the freezer compartment.(4)Lift up on the icemaker to remove it. (5)remove the white plastic cover from the front of the icemaker (pry out at the bottom) and snap it onto the new icemaker. (6)Remove the wire sensor arm from the old icemaker and place it on the new one. (7) Remove the cable assembly (plug) from the old icemaker and fasten it to the new one. (8)Secure the new icemaker in place using the reverse order as the removal. The icemaker will take a little longer to make its first batch of ice as it will have to attain its proper operating temp (0 degrees to 2 degrees F).

Followed your internet instructions. Saved $1200!!

Removed ice bucket from my freezer and poured ice out into a small ice chest. Unsnapped access door assembly from old ice bucket and then removed the 4 screws holding the front of the auger assembly. (Note that 2 screws have points and 2 have flat ends. The ones with flat ends are at the top and extend into the ice bucket area where you could contact them with your hand if you reached into the ice bucket area.) I screwed the auger assembly onto the front of the ice bucket and then snapped the front access door assembly onto the new ice bucket. Refilled with ice from ice chest and replaced ice bucket into my freezer.

remove right door replace lower door cam

Logged in to internet, for whatever reason I selected your site. Good choice! Entered the model number and selected the symtems identical to my refrig. Ordered the recommended parts, (Relay and Start Capacitor), to solve the problem. Reviewed the remove and install video. Received parts as promised by del date. Installed parts under 15 minutes, Frig kicked in and frig has been working beautiful. Avoided all those added expenses of; home service check, amount of days in- shop repair, plus parts and overhead charges. Will recommend site to my friends.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.