JCB2282KTB Jenn-Air Refrigerator - Instructions

Took longer to move food from door to inside fridge & take grandkids' artwork off door, & then put it all back than it did to replace cam.
1. Used phillips head to undo 1 screw holding cover over top bracket; lifted off cover.
2. No need to have someone hold door while you remove top bracket; magnets in door gasket will hold it tight to fridge. Used socket to remove 3 screws in top bracket & lifted bracket up off top of door.
3. Door's not heavy. I stood on a sturdy chair to get better leverage. Opened the door enough to break the magnetic seal & llfted it up off bottom bracket. I moved it over just enough to get to the cam, rested the bottom of the door on the floor, & leaned it up against the open front of the fridge to help preserve chilled food.
4. Removed the 1 screw holding in the bad cam to the bottom bracket (uses smaller socket than screws on top bracket).
5. I checked part that goes up inside bottom of door & it was fine, so did not replace it.
6. Trickiest part: putting the door back on. I put a hand mirror on floor by the right corner & facing up so I could see the underpart of the door as I lifted it eased it down on the right place.
7. Closed door, made sure it was straight, replaced top hinge & cover, food, & artwork.

It was great. We replaced the thermistor A little difficult to get to the thermistor but once we found it five minutes. My refrigerator seems happy but we will monitor it and see.

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

Refrigerator was stored for about 2 years and we picked it up when the owner decided to move into an apartment and no longer needed to unit (lost home to foreclosure). Brought the unit home and it worked great for about 3 days. On the third day my wife noticed a slight electrical burning smell. I did also and quickly emptied the unit and hoped for the best. The unit did indeed stop working. I fancy myself a do it myselfer but I would normally not go near electricity but thought what the heck it was free if i ruin it I would give it away. After a little research i found Partselect and they had a great design and a few stories that sounded similar so i pulled the relay capacitor for the compressor and sure enough the unit showed burn marks where the unit had shorted out. Maybe a bug got in there or water, dirt but I ordered the part. I arrived in two days which was great. I installed the part and plug the unit in and crossed my fingers. Very happily the unit clicked on and has been running great ever since. thanks Partselect, while I may not be one of your big customers I will refer anyone with appliance issues to your site first.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

I loosened the two top screws, removed the bottom screw, lifted up on ice maker and slid it off, unplugged the wire from refrig. I transfered the wire to the new icemaker, pluged it back in, placed it on the two screws, installed lower screw, tighten top screws. Total time spent less than 15 minutes. The ice maker cost $125.00 with freight. Sears wanted $374.00

Removed door. Removed old cam closure assembly. Noticed that there was almost nothing inside the door for screw to screw into(only styrofoam insulation), which is why original screw backed out. Bad design. Got longer screw at bigger diameter. Pushed high strength glue into hole, on screw threads, and underneath screw head. Assembled. Crossed fingers. About three weeks have passed and so far, so good.

first I removed the panels to see if the coils were getting frosty . Then I noticed that the fan was not spinning. I tested voltage to the fan and it was hot. I ordered the new fan put it in placve and, voila!.
Fixed my fride for under 50 bucks

Popping out the broken switch was easy once I was able to see how the new switch part was engineered. The switch was made to be replaced, having a simple tension hook on the bottom of the switch which needed to be depressed to pull the switch out of the cabinet. Once pulled out, there were modular plugs for the power line that were easy to pull off the broken switch and plug into the new switch. Pop the new switch back in and VOILA, the lights worked again! Thanks to part select's good diagrams of the actual model of my refrigerator, it was very easy to hone in on the exact part I needed. I did notice one problem with the order as the correct series for the part was displayed earlier in the process, but had the wrong series later in the process. However,. I trusted the system and the part is for the right series and fit well (an exact match, down to the color). Thanks Part Select, I would definitely use you again.

(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!

Pop loose the plastic grate at the bottom.

Locate and remove the wheel leveling screw from the front bottom corner.

Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.

Lift out the wheel assembly.

Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.

Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.

Reinstall and adjust wheel assembly.

noticed the fridge and frezzer were not cold one day.i got on google and typed in the problem and found out the the relay goes bad rather often. was an easy fix. found the parts here on partselect and recieved in with in 2 days of ordering. pulled the old part out put new part in and plugged fridge in and was back up and running with in minutes..thank you partselect....

I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98.
So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.

Went on line to find replacement valve.
Received the new part and compared to broken part. Both the same.
CAREFULLY removed the broken valve. Paying attention to how it came off.
CAREFULLY put it on the same way it came off.
This is a plug and play part. Just had to reconnect the water line.
Saved at least 75 dollars.
Easy to find the part on your site.