JCB2058GEW (PJCB2058GW1) Jenn-Air Refrigerator - Instructions

Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.

Refrigerator was stored for about 2 years and we picked it up when the owner decided to move into an apartment and no longer needed to unit (lost home to foreclosure). Brought the unit home and it worked great for about 3 days. On the third day my wife noticed a slight electrical burning smell. I did also and quickly emptied the unit and hoped for the best. The unit did indeed stop working. I fancy myself a do it myselfer but I would normally not go near electricity but thought what the heck it was free if i ruin it I would give it away. After a little research i found Partselect and they had a great design and a few stories that sounded similar so i pulled the relay capacitor for the compressor and sure enough the unit showed burn marks where the unit had shorted out. Maybe a bug got in there or water, dirt but I ordered the part. I arrived in two days which was great. I installed the part and plug the unit in and crossed my fingers. Very happily the unit clicked on and has been running great ever since. thanks Partselect, while I may not be one of your big customers I will refer anyone with appliance issues to your site first.

For replacing end cap, LH pantry part:
removed large pantry drawer
removed two small upper pantry drawers
removed glass panel and long braces---all these parts required no tools
used 1/4" nut driver to remove 3 screws from broken end cap, LH pantry part and shook it to release it from the refrigerator
used phillips head screw driver to remove drawer arms
replaced metal drawer arms to new end cap, LH pantry part
attached new end cap, LH panrty part to refigerator and finised by using nut driver on all 3 screws. then replaced other pantry dawers, glass shelf, and pantry cover. EASY!

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

Ordered new drawer -- fast and easy to find the correct part on this site. I also felt that the price was very reasonable.
Except for one thing, it would have been simple to slide the new drawer in.
The original drawer has a white plastic "face" that is removable.
"Removable" is a relative term. It took my wife and I over 20 mins to very carefully remove the face without breaking. One person could not do it --- you need to hold the drawer firmly while another pries the face off carefully. Once off, it was able to be pushed on to the new drawer -- be firm.

I loosened the two top screws, removed the bottom screw, lifted up on ice maker and slid it off, unplugged the wire from refrig. I transfered the wire to the new icemaker, pluged it back in, placed it on the two screws, installed lower screw, tighten top screws. Total time spent less than 15 minutes. The ice maker cost $125.00 with freight. Sears wanted $374.00

I ordered a new crisper drawer from PartSelect over the internet one morning at approximately 10:00am, and the product was delivered, non-express delivery, the next day at about 4:pm. The front coverplate of the old crisper came off easily, and snapped into place on the new drawer easily. The entire repair/replacement took less than 5 minutes.
Service from PartSelect, from locating, to ordering, to rceiving the part could not have been simpler or more efficient. A 5 star experience.Thank you.

Pop loose the plastic grate at the bottom.

Locate and remove the wheel leveling screw from the front bottom corner.

Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.

Lift out the wheel assembly.

Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.

Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.

Reinstall and adjust wheel assembly.

noticed the fridge and frezzer were not cold one day.i got on google and typed in the problem and found out the the relay goes bad rather often. was an easy fix. found the parts here on partselect and recieved in with in 2 days of ordering. pulled the old part out put new part in and plugged fridge in and was back up and running with in minutes..thank you partselect....

(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!

Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.

I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98.
So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.

Removed the hinge cover, removed three hinge screws, removed door. Then I used a screwdriver to pry out the hinge bushings, pushed the new ones in and replaced the door. Both Maytag and Lowe's (who held the extended warranty) said that the door was not a repairable item and would have to replace the whole door. Since that would cost more than the value of the fridge, they voided the warranty and returned my cost. Too bad we didn't know about Part Select, we would have held their feet to the fire.

It is simple, unscrew the old screw in the new one.

Once I figured out where the part was located it was quite simple. I thawed out the freezer first. Using a nut driver, I removed all the screws to the back panel of freezer. Squeezed the clips on the ice maker attachment to release the panel. Once I opened the panel the thermostat was visible and accessible. The failed thermostat was obvious by its bulging appearance. By following the instructions found on Partselect.com, I cut the two connecting wires and removed the failed part. I then striped some insulator from the wires to connect the new part. I used electrical tape to ensure connection and insulation as the white wire connectors did not work well (too big) for my application. Closed everything back up, plugged in refer and all was good. A little time and a $20 part saved me $150. Thanks Part Select!