Models > HDA2000F04AD > Instructions

HDA2000F04AD Hotpoint Dishwasher - Instructions

All installation instructions for HDA2000F04AD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA2000F04AD
1-15 of 573
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The rollers on the upper rack broke

  • Customer: Carl from Fairfield TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 462 of 463 people found this instruction helpful
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece then slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the
guides.

Lower rack wheel was melted

  • Customer: Mark from Huntingdon Valley PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 461 of 462 people found this instruction helpful
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.

Wheel broken off bottom rack

  • Customer: Julie from Maumee OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 460 of 460 people found this instruction helpful
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done!

The rear wheels were missing on the lower rack.

  • Customer: Teresa from Phenix City AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 458 of 460 people found this instruction helpful
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.

Broken upper rack roller, rack kept falling off the track

  • Customer: Doug from Columbus OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 371 of 374 people found this instruction helpful
Used the pliers to remove the broken roller. It came off in pieces. Slid new one on.

Cap on end of roller track was a bit of a challenge. It sort of twists & pulls off.

Rollers fell off lower rack of dishwasher.

  • Customer: Lloyd from The Villages FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 362 of 363 people found this instruction helpful
First removed four old wheels. then attached four new wheels to lower rack by pressing into slots.

The stud assembly in the middle of each wheel no longer stayed inside the wheel.

  • Customer: Wendy Baldwin from Stowe PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 361 of 365 people found this instruction helpful
Just pulled off the old wheel. I just had to push in the stud to the wheel and pushed it on to the rack of the dishwasher. Very easy repair! Only disappointing part was that it bothered me to have to purchase the stud with the wheel. I was told they only came as the set. I only needed to purchase that inside stud. My wheels were fine.

Rack falling off of upper slides

  • Customer: Eric from Centreville VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 188 of 256 people found this instruction helpful
1. I removed the plastic stops from the ends of the upper rack slides.
2. Removed the upper rack.
3. Unclipped the old rollers from the rack.
4. Clipped the new rollers onto the rack.
5. Made a grunting noise so the wife could hear.
6. Walked away

wheel replacement

  • Customer: michael from perry hall MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 216 of 404 people found this instruction helpful
Pulled the end cap off and replaced the wheel.
most of the parts were for future repairs

Water leak from gate (diverter) valve shaft

  • Customer: Joseph from Livermore CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 84 of 92 people found this instruction helpful
This was a fairly simple repair. After disconnecting power to the dishwasher and removing the panel below the door, first had to remove a retainer C clip from the gate valve shaft. Then disconnected the linkage from the gate valve solenoid, removed two return springs and slid the gate valve contol arm off the shaft. Then removed the solenoid bracket that was fastened to the housing by 2 screws. This allowed access to the push on nut on the valve shaft. Removed the old push on nut which exposed the leaking seal. Removed the bad seal, then moistened and carefully slid on and seated the new drain valve shaft seal. Affixed new push on nut. Reinstalled the above mentioned parts that were removed. Problem solved - no more leak. Total cost $18.81 for factory GE parts plus $6.95 shipping. Thank you PartSelect.

wheels were worn out and kept falling off

  • Customer: JOHN from PURCELLVILLE VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 66 of 68 people found this instruction helpful
popped old wheel off popped new one on
for the rack roller i took the ends off and slid old rollers off then slid new ones on.

roller on upper rack broken - lower rack plate holders broken

  • Customer: charles from canton MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 89 of 158 people found this instruction helpful
lower rack took one min. take out old slide in new

upper rack a little tricky had to remove end caps on rack arms to slide rack out to replace rollers. end caps are not snapped in they have a lever in the track that is part of the cap if you twist it a little cap will slide off.
total time for this part 15 min.

front twoo rack rollers broken ,bottom rack roller broken

  • Customer: Russell from Pueblo CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 74 of 136 people found this instruction helpful
for the top rollers you must remove thethe end cap. this was easy ,i placed a block of wood on the outside .placed the punch on the inside where the channel is pushed in to hold cap on. smacked it till it was pushed out far enough to remove end cap. new rollers simply snap on. very easy,

lower dishrack rusted

  • Customer: michael from Bloomington IN
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 43 of 47 people found this instruction helpful
replaced rack, no repairs required

Dish washer is not running through cycles

  • Customer: mike from huntley IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 45 of 55 people found this instruction helpful
First and formost before you buy read everything in trouble shooting your dishwasher. Then you do not buy parts you do not need. First you turn off power, then water. Remove two screws, a rubber hose and a hard line by unscrewing if you are lucky some contractors might sweat this on. No biggie just two extra steps that's all. do in reverse to assemble...
All Instructions for the HDA2000F04AD
1-15 of 573