Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Frost and ice was building up on the top of the ice chute inside the freezer
There is a plastic flapper valve that is spring-loaded in the closed position that prevents ambient room air from entering the freezer compartment via the ice chute. The Ice Chute Seal is a simple flexible (rubber-like) disk that just slips over the circular flapper valve. With the freezer door open one can see the flapper valve down the ice chute and one can reach it easily from the outside of the freezer as well. The Ice Chute Seal has 3 notches that make it very easy to remove the old seal and replace it with the new seal. This can be done by feel. I removed the old seal by pushing the flapper valve open with one hand (from the inside of the freezer door) and could then peel off the seal surrounding the flapper valve with the other hand. Once the old seal was removed I slipped the new seal around the flapper valve. No tools required, no screws needed to be removed. The problem I had with frost/ice build-up was solved; there is no more ice/frost build-up inside the freezer near the top of the ice chute. The old seal LOOKED OK but was obviously a bit too stiff to seal the opening against the warm, moist, ambient room air. I was most happy to see that this solved the problem and that it was so easy to do (really less than a minute or two!).
Killed the power to the fridge. Then, used a small, thin screwdriver to depress the clip on the bottom of the switch and wriggled the old switch out. The two wires easily came off the contacts with pliers. Connected the wires to the new switch and snapped it into the hole--clip facing down and contacts facing up. Turned the power back on and checked the switch. Worked perfectly! Easy job.
Water line feeding ice maker was not producing ice
Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.
pull open seal lift up release bottem catch push in to release top catch clean disk and installnew seal put back in the reverse of taking out dont take any thing else apart
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.
I checked the element and the thermostat and determined the problem to be the control board. I simply followed the instruction in the video. Everything went well until the last step, the video said to push the freezer down button. When this did not work I refered to the written instructions which told me to push the up button. That did it. Job complete. The unit is working as it should.
the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!
I replaced the Control Board... the two boards need to be installed first . than plug in the connectors (refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
Lip of ice bucket kept breaking off and pieces would jam dispenser.
Took longer to pull fridge out and push back than to replace bucket. Pull bucket and dispenser out . Carefully unsnap plastic front cover and access door from bucket. Loosen two hex screws that attach bucket to dispenser. Auger assembly comes loose. Just reinstall auger and screws then carefully snap front back on. Slide unit back in freezer.Push fridge back in place. Take a beer out of fridge. Drink it and pat yourself on the back!
About twicw per year the freezer would ice up because the control board didn't activate the defrost element
Removed the cover using a mirror to see how to release the clips on the rear side of the cover, removed the circuit board noting how everything was installed and also visually verified the part was the same. Broke the circuit at the designated score, installed and followed instructions for programming. All is well now.
