GY395LXGQ3 Whirlpool Range - Instructions

Followed instruction on web site

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

I did the repair following your instructions and it went very well. Now the temperature is working good , but the oven is heating up very slow. So now what should I do to fix the oven?

The part came in 2 days even though I chose the least expensive shipping method. The hardest part was unscrewing the old screws that held the old bake element in place. We soaked them in WD40, and after a while were able to unscrew them. The new element slid in place and works just fine.

The oven light gasket had deteriorated with time and bulb changes. It is a self cleaning oven, which gets very hot during the cleaning cycle. The oven is old (27years) and off the "books" I selected a similar, but slightly smaller gasket (3" OD), and "fit" it to the 3.5" light fixture of the older oven. The gasket material was similar to the original, and I used a usable portion of the original,along with the new gasket to build a gasket for the light lense. Several years prior to this repair, I replaced the oven door springs. Whirlpool, who had taken over what was left of Chambers, had the springs. I did replace one heating element about 15 years ago. The Chamber's salesman told me that the Chambers was the "Cadillac" of all ovens, and it seems to keep running.

Step 1. Always ensure appliance is unpluged from power source. 2 Remove oven door by open slighly and lift up be sure your hands are up from hinges they can snap back and injure fingers. 3. Have a cover on a flat surface and have a diagram of oven door, 4. Remove bottom screws and slide out top glass and side rails. 5 Remove top cover and insulation over glass. Beware of any jagged glass. 6. Incert new glass. 7. Be sure when replacing insulation and cover that cover in under tabs to ensure glass is firmly held in place repeat steps in reverse order. Took just 20 minutes to repair. I used a small electric screw driver.

Had to screw off old terminal block & screw on new one

I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.

Took door apart no problem had a little trouble putting it back together just one piece I put back wrong had to start over not to bad still took less then one hour

I was not around the entire time a neighbor was working to get the door removed. He only said he had to remove an additional screw so I'm not sure I can be of much help here.Once the door was removed however, the repair went easily. I would tell anyone needing this repair to be prepared to clean a number of crevices around the door. I was glad to have a chance to clean these hidden places.Let me also said customer service rep was wonderful.

Sensor matched perfect, but had to pull large upper rear panel to find location. From there took a few minutes to reassemble back. Did not un hook gas but turned it off. Obviously unplugged power. Oven works fine.

I took the back plate off of the oven by removing 3 screws and removed a single screw holding the sensor element in place, plugged the electrical 2 prong terminals back together and re-assembled the back of the oven. After the installation was completed we did a test run. It worked for aprox. 15 minutes and shut off again. It must have re-booted its self, cause when we tried it again it worked and still is working.

The Temperature Sensor was actually installed from the back of the oven. I had to remove about six(6) screws to remove a metal panel on the back of the stove. The connector the Temp sensor came with did not match the existing connector however it did come with wire nuts as an alternative. I cut the wires and connected them with the wire nuts and replaced the pannel. Very easy fix and my 13 year old oven still runs like new.

Replaced both rollers....Quick and Easy!!