GWRE6270H0WW General Electric Washer - Instructions

This job did not take much longer than 15 minutes if that.1st take the cord or twine and loop it under 2 paddles of the agitator.( there is a small groove under each of the paddles that has enough space to put the cord in) Pull up on the cord to remove the agitator. 2nd. Under the agitator is a bolt that secures the agitator coupling. Remove that bolt. Keep bolt(you may want to replace this bolt if rusted and worn. Mine was still ok so I reused it.) 3rd pull up on Agitator coupling to remove. Teeth were worn on Coupling, So discard. 4th Insert new coupling, replace bolt to secure coupling. finally slide agitator back over coupling till locks back in place. ....Done.

DISCONNECT POWER----1.- No pump sound when energized but I know it energized as the coil became a magnet. 2.- You need a drain pan to catch the water from the lower tub when the drain hose is disconnected from the pump. 3.- Water pump or channel lock pliers needed to remove the spring clamps on inlet and outlet from pump. 4.- Remove the 2 hold down bolts and the plug in power connection and the pump comes out very easily. 5.- On my pump I found a plastic tie wrap lodged in the pump impeller vanes-- this caused the pump either not to work at all or cause a cavitation effect caused the water in the tub not to drain completely. 6.- Since I had already purchased the new pump I installed the new pump and cleaned the old one to keep as a spare-- probably never going to need it though.7.- On the large diameter drain hose ( pump inlet ) I decided to use a auto hose clamp instead of the original spring clamp because the area to work on this pump is very cramped and getting the original spring clamp back on was very difficult. The hose clamp made it very easy and the seal was just fine. 8.- The new pump functions perfectly- PARTS SELECT delivered a quality OEM product and I am extremely satisfied with their normal delivery which was 2 days because the warehouse was only 150 miles from me.

I searched the internet for the problem resolution & purchased $40 of the parts before I disassembled the machine. This was to minimize the downtime. Not one of the internet sites recommended changing the shaft & mode shifter assy so all the parts I ordered were not needed. Once I determined the correct part I had the reorder & pay expediting fees to deliver next day.

After watching the YouTube video on how to disassemble the GE Profile washing machine the repair was relatively simple.

First I removed the softener dispenser then I grabbed the agitator at the bottom and with a tug completely removed it. I took the new part out of the box and lowered it down over the hub in the bottom of the washer and gently pushed it until it snapped in place. Then I re-installed the old fabric softener dispenser and the job was complete.

I laid the washer on its front and removed enough screws to fold the bottom out enough to reach it. I used a wire tie to secure the belt to main pulley and slipped it on the drive. This would have been nearly impossible without the install tool as it stopped the belt from slipping off of the drive. It was simple to turn the pulley clockwise to walk the belt onto it. The whole repair took about 1/2 hour, would have been less if I had used the wire tie at the very beginning.

order part. replace

I watched the video you provided and I could't believe how simple it was. I'm 67 yrs old and I just followed the video instructions.

We couldn't get a repair to come out - were told to buy a new because it would cost too much to fix. I did not agree. I pulled the agitator off and discovered it was not working and the agitator coupler was spinning. I ordered both and put them in myself. My washer now worked like new! All for less than $100. The service guy wouldn't eve come out for less than $175 and that did not include parts!

Take front of machine off, unscrew bottom and lay out just enough to get under the machine you do not have to take it completely off. After that unscrew center bolt holding wheel and wrap belt around then attatch the belt to the power spinner pull down as best you can and reattatch the wheel and bolt back up.

I just popped in the new agitator. The coupler wasn't needed but I will keep it just in case.

I removed the agitator, replaced the agitator coupling. The guy at the appliance store where I was able to find the part said to check the splines on the inside of the agitator as well. Glad I did, the splines on the agitator were worn out too. So by checking both, if and when the problem occurs, REPLACE BOTH parts! This will save a lot of grief for you!

Was very easy to remove and replace. The instructional video let me know what to expect

Unit unplugged. Next day delivery, saved plastic clip and two screws from hose connect to washer , removed leaking hose ,replaced with new hose fully pushed into unit with plastic clip already in place on new hose. Tightened screws on plastic holding clip on new hose. Done complete job in 5 minutes.