Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Trial and error. IT would have been nice to have instructions with the part. Tried to install the gasket withour completely removing the frame. Wasn't happening. Finally removed the frame and repair went fairly well.
First, I removed everything from the door shelves. Next, I loosened the screws around the door, under the seals, pulled the seals out and slid the new ones into place. It couldn't have been easier. There is no need to remove the door liner. It's like having a new refrigerator.
I was surprised, when my parts arrived 3 days after I ordered them. The cost was less than half, compared to our local parts house.
First I removed all the screws from the back cover. 2nd removed fan nut and fan blade 3rd removed fan bracket 4th I traced wire to the condenser and disconnected wires from wire nuts. Installed existing fan brackets to new motor kit then reconnected wire nuts to new motor cord Reinstalled fan nut and blade, reinstalled cover, plugged it in and BAM .WORKS PERF!
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Outer case of freezer was heating up, not making ice (sometimes) turned up thermostat several times (especially freezer)
I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.
Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well
Exposed evaporator and fan.Turned refer back on. Evaporator started to get cold but fan did not run. Removed fan and applied 115 volts. Fan did not run. Installed new fan kit. Old refer works as good as new. Vary easy job. I almost bought a new refer. Glad I didn't. Probably saved myself $500+ Shopped several sites on internet. Other sites wanted about the same price for motor only and 15-20 bucks more for the fan. Vary pleased that I found this company to buy this part. Received fan kit in just a few days.
did not remove the doors. did freezer first ,removed inner door planel install gasget on panel and reinstalled. the aloney problem i had was trying to resape the door gasget on the big door. which is still a little out of shape hopeing it will fall in line over time.
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
I ordered the post, pulled it out of the box, pulled off the glass, pulled out the drawers. I looked at where the post looked like it shoul go and put it in. put the drawers in, glass on. It took me about 5 minutes and everything is perfect.
I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.
Had wife remove all the food from the bottom of the refrigerator. Removed the glass shelf , two drawers and the frame that they all sit in. Removed old broken crisper rail and replaced it with the new one, after I installed the wheel that the drawer slides on. Put everything back in place then called wife to put food back in where she wanted it.