Models > GSL25JFPABS > Instructions

GSL25JFPABS General Electric Refrigerator - Instructions

All installation instructions for GSL25JFPABS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GSL25JFPABS
1,516-1,530 of 1,623
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

freezer not defrosting

  • Customer: JOYCE from REEDSBURG, WI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Only problem we had was when we removed back wall on freezer the couls were totally iced up. After waiting for that to defrost. (3 HOURS) repair went fine. Was kind of hard to get to the part being its a side by side but happy with results

fridge and freezer not staying cold

  • Customer: Ralph from Whittier, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed back panel from freezer. located thermostat removed and replaced thermostat put panel and all baskets back into freezer and plugged fridge back in. Works perfect problem solved

coils in the freezer kept freezing up

  • Customer: rob from modesto, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
by luck i found this very informative website.found the parts i needed and got the job done.i defrosted the freezer coils and made the repairs following the instruction video that was emailed to me by this company. very easy to make these repairs.cost me less than $100 to fix compared to a $90 service fee, plus part,plus labor. Thank you so much!!!!

Running hot

  • Customer: Ken from Cloverdale, IN
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
The mother board was bad....solder the board and it works like a charm.

Refrigerator and Freezer were not staying cold. Condensor was completley iced up.

  • Customer: Michael from Oconomowoc, WI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Emptied Freezer (to get access to panel covering condensor coils and Defrost Thermostat). Pulled off cover panesl. Had to wait for ice to clear from condensor. Replaced Defrost Thermostat (5 min job), replaced panels and was back in business.

Ice maker not making ice and leaking

  • Customer: Andy from Ft Pierce, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I took off the front cover of the icemaker assembly and found that the gears were not meshing properly and therefore slipping. I removed the front panel and found that the white plastic cam unit under the large gear wheel had disengaged from the hole in the front plate which is why the gears were slipping. I refitted the cam and wheel and it worked fine but stopped again for the same reason the next day. As the plate appeared to be buckled somehow (not user repairable) and, as the unit was leaking and pooling water (which froze) in the collection unit, I decided to change the whole icemaker.

Ordered about 1300 on a Thursday, it arrived the next day at noon and was fitted straight away. As others have mentioned, the extension cable required to fit into my old fridge made it quite cumbersome however with a bit of juggling and persuasion, I got it to fit into the cut out corner of the ice container so it is completely out of the way. Job done in about 35 minutes, making ice in an hour.

Ice Maker not making ice

  • Customer: George from Katy, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The video on the GE site was great. Showed step by step instructions on how to remove the old ice maker and install the new one. Also helpful was the detail on the water chute which needed to be moved from the old ice make to the new one. Saved hundreds of dollars by not having to have a repairman do this work for me.

ice maker was leaking water. Cubes were sticking inside tray.

  • Customer: Carl from Abilene, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!

Ice Maker stopped working

  • Customer: William from San Tan Valley, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took out one hex screw, disconnect electric couplings, pulled original ice maker out and found that the water supply line to the ice maker was frozen solid as well as the shute cup. Used hair dryer to thaw out the line and the cup reinstaled old ice maker and it worked fine. Did not have to use the new part at all at this time. Am keeping new part for future use.

Refrigerator and Freezer warming and cooling. Ice would melt and then refreeze. Freezer temp would warm to 25 then back to 0, refrig temp would warm to 50 then back to 34.

  • Customer: Patrick from Tomball, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We first read that we should thoroughly clean the coils which we did. They were very dirty, full of dust. This seemed to help for a couple days then the hot and cold started up again and was even worse. We did some research on the internet and all indications led us to change the main control board. We found PartSelect ordered the part, received it super fast (within 2 days), changed the part in less than 15 mins and our refrigerator works like new. No trouble since the repair. Saved a lot of time and money doing the repair ourselves.

some time ago the ice maker stopped dispensing ice followed by water no longer dispensing

  • Customer: Gregory from Winchester, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I used the repair video supplied on line. I followed it step by step and the repair was made quickly and easily. Best of all I saved the expensive cost of a repairman.

The refrigerator/freezer were not getting cold after the circuit breaker tripped.

  • Customer: Stephen from Northridge, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Based on the site, I figured the problem was the electronics board or the defrost sensor. After some multimeter work, I was pretty sure that it was the board; however, the defrost sensor was inexpensive so I bought both. I watched the videos, and the work was pretty much the way it was described. No problems or unforeseen issues.

ice maker and water dispenser stopped working and the fridge made a clicking sou nd as if something was turning on and off, got online and read faqs determined I needed a new mother board. nd

  • Customer: van from sandy, UT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I simply took out the old board as per video instructions. very easy . unplug 6 or seven connectors and ground wire slap in new board and reconnect . even a cave man can do it.

Refrigerator was not cooling

  • Customer: Barry from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Had a repairman come out and quote me over $600 to replace the control panel and the display. I went online and found you guys, watched the video, and replaced the control panel in less than 15 minutes. Your video was great and gave very clear instructions - unplugged the fridge, unscrewed the panel on the back, popped off the control panel and connectors using needle-nose plyers, put new control panel in place and reconnected all the plug-ins, put cover panel back on, plugged fridge in, reconnected and checked display inside front of fridge, it came on and lit up, closed the door and let the fridge cool to the proper temp. The fridge is now working great for around $175 for parts. Thanks!

My refrigerator suddenly stopped dispensing ice and water

  • Customer: Timothy from Birmingham, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I did an internet search on the issue, which was that my refrigerator suddenly stopped dispensing ice and water through the door. Also, the refrigerator had been cycling on and off constantly for some time. I found a YouTube video showing how to replace the main control board; along with a link to order the new part. I ordered the part and selected standard shipping. My part arrived in 48 hours. I replaced the main control board just like in the video. My refrigerator works like new now. I was able to solve my problem in two days on my own, for the cost of parts only. I am sold on PartSelect.com.
All Instructions for the GSL25JFPABS
1,516-1,530 of 1,623