GS440LEMT3 Whirlpool Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
temp sensor went oven not heating
-
patrick from HUGHESTOWN, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Whirlpool gas stove burner igniter had broken.
Our existing gas stove burner igniter had broken on one of the four burners. I therefore obtained a replacement igniter and mounting screw form PartSelect.com which were indeed perfect replacement parts. However, I could not remove the burner plates from the top of the stove since they were basically welded into position by years of heat. I therefore followed instructions as submitted by a previous customer (thank you Michael of Bloomington, Il), snapped open the stove lid retainer clips, and then lifted the stove surface about 4 inches. Through that opening I was able to reach the underside of the involved burner. Unfortunately, I could not unscrew the existing broken igniter mounting screw and therefore had to break off the already broken igniter and grind down the remaining mounting screw using a drill grinder since the screw was basically welded into place. Once I did that, I was then able to install the new igniter using a separate unused screw hole already in place right beside the old previous mounting screw. With that done, the new igniter works perfectly and the burner works just like new. It was however a lengthy process over two hours long because of the glitches described above. Nevertheless I'm very pleased that the parts were perfect and the repair is complete.
Parts Used:
-
Jeff from DEER PARK, WI
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
4 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven not keeping correct temp and sometimes would not relight when temp went dropped.t
Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.
Parts Used:
-
Gary from PLUM CITY, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Parts Used:
-
Yafa (and David) from Bothell, WA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
5 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Rear Drawer Glide
This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.
Parts Used:
-
Ed from Maple Grove, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken drawer glides
Simply removed the bottom drawer, unscrew the old broken glide, and attach the new glide. Simple and no hassles.
Parts Used:
-
Shane from Palatine, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Paint peeling from strip
-
Myron from Punta Gorda, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not maintain Heating
Following details from the installation video, after removing the main gas line and the two output lines I removed the four screws that removed the valve but found it was easier to remove and install the new one if I first removed the oven burner(it made for lining up the valve nozzle to the burner easier) from the inside, 3 wires attach on the side towards the stove taking one wire from the old valve and putting it on the new valve in the same place. Everything went back together just fine, I did have some problem with tightening one of the two gas lines for the output and found I just had to keep tightening it a little until there were no bubbles appearing when I applied soapy water to the connections, other than that it was very straight forward.
Parts Used:
-
Cheryl from WEST JORDAN, UT
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would lite once and after that it would just click 3 times and nothing, click 3 times and the same thing!
Removed the bottom pan and heat shield plate, removed the drawer to get to the igniter disconnect the one wire from it and removed it and just repeated the same process backwards to put the new one in. All under 15 mins
Parts Used:
-
Robert from BUFFALO, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven not reaching temperature
Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place
Parts Used:
-
Marsha from Clermont, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace bake ignitor ; flame spreader removal difficulty
As the 2 screws in the front of the flame spreader didn't screw into anything , and made getting the flame spreader very difficult to remove, once I got the flame spreader out , I did cut off the screws so future install & removal would be easy. I had to hacksaw the screws off , as the screws are otherwise impossible to remove. The screws were damaging the oven metal sheet work during first removal ! Otherwise the new bake ignitor install would have been a very quick 20 minutes. Also I watched u-tube bake ignitor install & oven door remove videos, which were extremely helpful.
Parts Used:
-
Steven from SAN ANSELMO, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Peeling paint grate
-
Patricia from OLYMPIA, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Exterior glass of oven door broke spontaneously
We cheated; a local appliance repair company was called & the tech guy repaired it in 10 - 20 minutes. Couldn't be happier.
Parts Used:
-
Nancy from SAN FRANCISCO, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven would not completely heat up, only heating to about 150 degrees Temp.
-
Isaac from MATTESON, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas oven would shut off mid cook
Removed grills. Removed bottom plate.
Removed flame shield.
Removed igniter, 2 hex head screws. Bottom one is a bit awkward. Disconnected wire. Installed new igniter. Careful not to drop stuff in the hole. Like a socket. I did
Removed flame shield.
Removed igniter, 2 hex head screws. Bottom one is a bit awkward. Disconnected wire. Installed new igniter. Careful not to drop stuff in the hole. Like a socket. I did
Parts Used:
-
Glenn from ROANOKE, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!