Models > GR563LXSS1 > Instructions

GR563LXSS1 Whirlpool Range - Instructions

All installation instructions for GR563LXSS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GR563LXSS1
91-101 of 101
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Exterior Door Glass

  • Customer: Andrew from Riverside CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed old trim kit and handle installed new parts but was having problems with glass fitting between handle and bottom bracket there was a gap between glass and handle when installed fist time after disassembling again I found that the door frame it self had to be tapped back into alignment to be square but once the adjustments were made the installation was a breeze

Gas range would not go into self cleaning mode. When pushing the self clean button, would get three beeps!

  • Customer: Lee from Saint James NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.

terminal block back of range shorted and burned

  • Customer: Louis from Grantsville UT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare

THE PARTS CAME WITH NO INSTRUCTIONS AND WE COULDN'T FIND DIRECTIONS ON LINE.

  • Customer: Kathleen from Livingston MT
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
WE TOOK THE DOOR OFF AND TOOK IT AND THE SIDE PANELS TO THE LOCAL DEALER AND HE PUT THEM ON FOR US - FOR ANYONE NEEDING TO REPLACE THE SIDE PANELS ON THE OVER, BE AWARE THEY SLIDE UNDER THE GLASS FRONT -NOT OVER IT LIKE WE TRIED TO DO. WE THOUGHT, THOUGH, THAT WE WERE GOING TO HAVE A BUY A NEW STOVE BUT FOR A LITTLE OVER $70.00 WE GOT THE PARTS, HAD THEM INSTALLED AND SAVED OVER $800 ON A NEW STOVE - WELL WORTH THE EFFORT.

Oven Drawer Roller Snapped Off

  • Customer: Kimberly from Sandusky OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced both rollers....Quick and Easy!!

DUEL BURNER , INSIDE BURNER OUT

  • Customer: ROBERT from MOSINEE WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
REMOVED BURNED OUT BURNER, REPLACED NEW BURNER TESTED WORKS FINE

Trim piece on the botom of the oven was chipped in three places

  • Customer: Terry from Maple Valley WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I used the allen wrenches to block the hinges, removed the oven door and used the kitchen counter for a work station. I removed the trim piece at the bottom which released the side trim and oven glass front, and then reversed the procedure. It took more time to clean things than to do the exchange. My only issue is with Fed Ex who delived the first trim piece bent in the middle inside a crushed box. Part Select had another part sent the same day after I called them.

The Range took forever to achieve the proper heating temperature with an inability to maintain a steady heat

  • Customer: Robert from Mifflinburg PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.

BOTTOM DOOR TRIM RUSTING

  • Customer: Dennis from Grimsley TN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I remove bottom trim which is held on by 3 screws and try to install new bottom trim, did not work well. I then remove yop handle assem. then the door glass which you need to clean after. Then install the new bottom trim then insert the glass into the new bottom strip using masking tape to hold the glass and side strips in place prior to installing the the top handle piece which is held on by two screws. Not a hard job to do.

Broken drawer handle

  • Customer: Nick from Chapel Hill NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My son broke the drawer handle of our stove a few years ago. It took me a while to get this repaired because the first company we ordered from shipped the wrong product to us and did not allow us to do a return! The team at PartSelect had the correct product delivered in just a few days! Once I had the product on hand the repair was super easy. Thanks PartSelect for great service!! Nick, ShirtsThatGo

Terminal Block was melted where the cord had came lose.

  • Customer: Louise from Humansville MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.
All Instructions for the GR563LXSS1
91-101 of 101