Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!
Easy repair-removed hex nuts and and screws to pop out old part and replace with new one. New part works better than the original! 1st replacement part arrived with a broken piece, a quick, courteous phone call got a replacement sent out. It took a 2nd phone call to obtain the refund, but the customer care reps are efficient and friendly. I would order from them again for positive service reasons alone.
i removed the screw holding the drain pump to the wire that held the pump to the dishwasher frame, i then unscrewed the hose clamps that connected the pump to the drain hose and the other part of the dishwasher i disconnected the wires , put the other pump into place wired it up and now my dishwasher is as good as new .
Upper rack kept dropping from the wheels when we pulled it out
We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.
The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.
unscrewed dishwasher from cabinet, then I flipped dishwasher on it's side. loosen pump motor bracket arm on the end of the motor. loosen pump motor to pump conecter hose clamp and then unscrewed pump motor connector from dishwasher. To install I did the reverse. very easy.
Removed the unit from under counter and placed it with the door side down. Removed clamps/bands from the outlets on the sump and removed screws that attached sump to dishwasher tub. Reversed the process with the new sump and positioned the dishwasher unt=der the cabinet. Next step was to remove the arm and cover parts to the sump, then removed the old upper neck portion that stuck to a strainer. Then aligned the strainer to connect to the small neck of the sump and replaced items in the order from which they were removed.
1. Turn off water supply. 2. Remove the metal toe kick plate/insulation at the bottom of the dishwasher. 3. Remove hose to supply valve. 4. Take electrical plug off old valve. 5. Remove float valve because it was mounted it right in the way of the 2 screws on the inlet valve bracket. 6. Remove those 2 screws now you can get to them, and move the inlet valve to one side so you can get to the hose clamp for the rubber hose out of the valve going to the dishwasher. 7, Take the old valve and bracket out, mount new valve on the bracket, crawl back down on the floor, reinstall rubber hose and bracket, and float valve and finally inlet hose. 8. Turn water on. Check hose connections for leaks. Yep, outlet hose didn't clamp enough now, allowing a drip. 9. Repeat the whole process AGAIN. Replace little clamp with a REAL hose clamp, reinstall the thing again. No leak this time. 10. Test run dishwasher thru a cycle. Check again for leaks at hose connections. OK ? Reinstall insulation pieces and toe kick plate.
The first thing I did was watch the video on the removal of the old broken dispenser and I said to myself that it couldn't be that easy. Well I am going on 70 years old and I was going to call a local to fix it. I bought the new dispenser just to avoid the up-charge. When the conformation email got here with video and written instructions. I watched the video and read the instructions. Just after the part arived (ahead of scheduls) I looked at the machins and said wat the he** what is she going to do to an old man. Got my screwdriver (battery and reversable) and wouldn't you know it . It only took me less then 15 minutes to do the whole job. I can't thank them enough for the video. Wife asked where the part was and almost pased out when I opened the door.. lol Trust these people . They know what they are doing!!!