GKSR3140H0WW General Electric Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
knob stripped
-
Robert from Strasburg, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Water leaked into machine when idle.
1. Turned off water at wall and removed hoses from back of washer. 2.Removed three screws and laid dash panel forward onto towel. 3. Used pliers to slip hose clamp off of valve connector. 4. Disconnected two electrical connectors. 5. Removed two screws mounting inlet valve to washer and removed valve. 6. Reinstalled in reverse order. My only problem was a vibrating noise when hot water was selected. I found that the fit of the dash panel to the back of washer was torqued. I removed the panel mounting screws, made a better fit and added a dot of rubber insulation between the sheet metal parts where the screws attached. Success!!
Parts Used:
-
Stephen from Lewisville, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
cycle selector knob, teeth broken off
-
Harry from Palm Bay, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Belt ripped off
Step one: Order the Belt and the $10.00 tool that fits on the motor sprocket to keep the belt from slipping off. Step 2: Lean the washer back at about a 45 degree angle, you may have to disconnect the water lines to achieve this. This puts the machine in a good position when you sit in front of it as you are installing the belt. Step 3: Install the tool over the motor sprocket leaving the grooves exposed. The belt fits in these grooves. Step 4: Slip the belt over the motor sprocket first and than the large sprocket wheel behind. This will take a little muscle as the belt is considerably smaller. After a couple of attempts at rotating the big sprocket the belt kept slipping off. I than took a plastic tie and strapped it around the belt and the big sprocket wheel, this kept the belt from slipping off as I rotated the wheel. Once the belt is on snip off the plastic tie and you are home free.
Parts Used:
-
Greg from Hawthorn Woods, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The washer had quit agitating but was still spinning
This job did not take much longer than 15 minutes if that.1st take the cord or twine and loop it under 2 paddles of the agitator.( there is a small groove under each of the paddles that has enough space to put the cord in) Pull up on the cord to remove the agitator. 2nd. Under the agitator is a bolt that secures the agitator coupling. Remove that bolt. Keep bolt(you may want to replace this bolt if rusted and worn. Mine was still ok so I reused it.) 3rd pull up on Agitator coupling to remove. Teeth were worn on Coupling, So discard. 4th Insert new coupling, replace bolt to secure coupling. finally slide agitator back over coupling till locks back in place. ....Done.
Parts Used:
-
Lewis from birmingham, AL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
teeth on plastic cog broken
-
Debra from Forestburg, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Stripped plastic teeth in back of knob
-
Michael from Philadelphia, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Washer pump would not turn
DISCONNECT POWER----1.- No pump sound when energized but I know it energized as the coil became a magnet. 2.- You need a drain pan to catch the water from the lower tub when the drain hose is disconnected from the pump. 3.- Water pump or channel lock pliers needed to remove the spring clamps on inlet and outlet from pump. 4.- Remove the 2 hold down bolts and the plug in power connection and the pump comes out very easily. 5.- On my pump I found a plastic tie wrap lodged in the pump impeller vanes-- this caused the pump either not to work at all or cause a cavitation effect caused the water in the tub not to drain completely. 6.- Since I had already purchased the new pump I installed the new pump and cleaned the old one to keep as a spare-- probably never going to need it though.7.- On the large diameter drain hose ( pump inlet ) I decided to use a auto hose clamp instead of the original spring clamp because the area to work on this pump is very cramped and getting the original spring clamp back on was very difficult. The hose clamp made it very easy and the seal was just fine. 8.- The new pump functions perfectly- PARTS SELECT delivered a quality OEM product and I am extremely satisfied with their normal delivery which was 2 days because the warehouse was only 150 miles from me.
Parts Used:
-
joe from port jefferson, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Installation of fabric softener dispenser
My washer didn't come with a fabric softener dispenser. I found one on your website and purchased (the part arrived in two days). I popped the top off the agitator, lined up the notches on the fabric softener dispenser with the inside notches on the agitator and pressed down. Voila! Less than 5 minutes, no tools needed.
Parts Used:
-
Deborah from Shirley, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
freight train sound during spin cycle
I searched the internet for the problem resolution & purchased $40 of the parts before I disassembled the machine. This was to minimize the downtime. Not one of the internet sites recommended changing the shaft & mode shifter assy so all the parts I ordered were not needed. Once I determined the correct part I had the reorder & pay expediting fees to deliver next day.
After watching the YouTube video on how to disassemble the GE Profile washing machine the repair was relatively simple.
After watching the YouTube video on how to disassemble the GE Profile washing machine the repair was relatively simple.
Parts Used:
-
Steven from Madisonville, LA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
selector nob would not wouk
remove top panel, replace the compression clip, then replace'd the top panel, w/pliers, remove'd then plastic clip from the timer knob, remove old knob, install new one, DONE! I've never had a place that had all parts in stock, and at my door with-in 2 days! UN-BELEIVABLE! THANKS
Parts Used:
-
RICK from SPICEWOOD, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Teeth Missing on Timer Knob
I removed the plastic pin, took the knob off, put the new one on, then replaced the plastic pin. EXTREMELY easy.
Parts Used:
-
Bryan from League City, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
hole in hose
-
hirfa from lake worth, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!
I bought this second hand and it had no hose
I watched the video you provided and I could't believe how simple it was. I'm 67 yrs old and I just followed the video instructions.
Parts Used:
-
Maryellen from Englewood, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
broken knob and awitch
Removed rear panel replaced switch had to put larger wire terminals on the switch was large we than the old index. Replaced panel put new knob re.pair complete
Parts Used:
-
Clifton from Monroe, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!