Models > GI7FVCXWQ00 > Instructions

GI7FVCXWQ00 Whirlpool Refrigerator - Instructions

All Instructions for the GI7FVCXWQ00
16 - 30 of 224
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old refrigerator gaskets were worn out
I unboxed the replacement gasket set and inspected them for damage. Then I opened the left refrigerator door and grabbed the right hand corner of the old gasket and removed it. I then aligned the new gasket with the door and using my fingers pushed the gasket into the gasket grove. I used my thumb to seat the gasket. I repeated the process for the right door. Total time was under 15 minutes.
Parts Used:
Refrigerator Door Gasket, Right (Gray)
  • Ron from LIVERMORE, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
17 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Problem, time to replace water filter
Turned the old one to unseat and replaced with a new one in the reverse order.
Parts Used:
Refrigerator Water Filter
  • Ralph from Longmont, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
18 of 24 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice machine wouldn't dispense ice from the door.
Removed the broken coupling with the new one from your store. It took less than 10 minutes. The video you provided on the website was very helpful.
Parts Used:
Coupling Ice Bin Coupling
  • Linda from Jackson, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
18 of 24 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
coupling on water line thru freezer door cut due to moving Refg and having to remove doors.
Snapped the large end of the coupling onto the main line coming from the water source and snapped the other end onto the small line leading to the ice maker. Quick and simple.
Parts Used:
Tube Connector - 1/4 Inch to 5/16 Inch
  • Martin from Rutherfordton, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
21 of 35 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice buildup around freezer door gasket
Replaced with new gasket
Parts Used:
Freezer Door Gasket - Apollo Gray
  • Joseph from JACKSONVILLE, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
16 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old one was broken and kept falling off. Very annoying
Snapped new cover on.
Parts Used:
Kickplate Grille - Black
  • Kathleen from Gainesville, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
13 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old motor was not resetting back to proper position halting ice production.
Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!
Parts Used:
Icemaker Motor Kit
  • Kevin from Spring, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
13 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The bins on the door (ice maker side) became cracked
It was just a simple swap out with the new bins.
Parts Used:
Cantilever Bin
  • Joe from ALTAMONTE SPG, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
11 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Remove the water filter to install the bypass cap
Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.
Parts Used:
Refrigerator Water Filter Bypass
  • Phil from GREENFIELD, IN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
11 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer icing up .
Watched Partselect video of P-trap installation.Removed water line & back cover& disconnected wires to water solenoid .Removed old drain tube & old problematic rubber funnel. Used contact cleaner to clean rubber residue from drain line and used a little silicone to aide reassembly. Job went well thanks to video.
Parts Used:
P-Trap Drain Tube Kit
  • Rich from Lansing, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Wrench (Adjustable)
11 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice bin coupling cogs broke off
Remove ice maker from freezer, place on its side on table. Remove single screw securing coupling from shaft without removing shaft from housing. Remove old coupling, and attach new coupling using single screw.

This is a great time to completely clean the Ice maker bin and crusher unit.
Parts Used:
Ice Bin Coupling
  • Stephen from Oregon City, OR
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
10 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Six months in use time to replace the filter
It is simple, unscrew the old screw in the new one.
Parts Used:
Refrigerator Water Filter
  • Michael from Long Valley, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
13 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right hand door would not auto close.
Removed the top door hinge cover.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.

But this did not fix the problem. Will have to remove the door and inspect the inside of the door's lower hinge assembly.
Parts Used:
Door Closure
  • Bill from Murphy, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
16 of 31 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace water filter
pop open, unscrew quarter turn, screw new one in quarter turn, pop shut. duh
Parts Used:
Refrigerator Water Filter
  • Brenda from Spokane Valley, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
13 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken light switch
followed the instructions provided and that's it!
Parts Used:
Door Switch
  • Richard from West Warwick, RI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
10 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GI7FVCXWQ00
16 - 30 of 224
Back to Top