Models > GHW9400PW0 > Instructions

GHW9400PW0 Whirlpool Washer - Instructions

All installation instructions for GHW9400PW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9400PW0
61-75 of 310
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The knob that controls the wash setting broke

  • Customer: Richard from Tempe AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
It only took a few seconds to slide on the new knob after it arrived by UPS. The part arrived sooner than scheduled. Great service and product.

door latch error code

  • Customer: Gary from Sonoma CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 12 people found this instruction helpful
removed all the panels to change the door latch switch
plug in three plugs ...works great
Thank you

washer not drain or spin

  • Customer: LAURA from SPARTA KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 9 people found this instruction helpful
it was a really easy fix. unclamped the 2 hoses and took out screw, removed water pump. Connected two hoses back and set in place then screwed in locking screw. could not have been any easier.

Clothes came out dripping wet

  • Customer: Louis from Branford CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Just removed the bottom cover to access the water pump. Drained the water through the filter housing. One screw and two hose clamps and the pump was out. Installed new pump and checked for leaks. None found so the cover was secured in plase. Great news, WIFE is happy.

Baffle in washer tub broke off

  • Customer: MIKE from BENBROOK TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
Snaped new one in place and done.

Low water intake pressure error

  • Customer: John from Rye Brook NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 4 of 4 people found this instruction helpful
Serviceman had previously replaced the hot and cold inlet valves, but the low pressure error persisted. Rather than cough up another $130 for the serviceman to return, plus parts and time, I decided to order the replacement flowmeter from PartSelect.

Unplug power and turn off water. Top of machine comes off by removing three screws at top rear; use socket, spanner or T20 driver. Unplug electric sensor from flowmeter. Old unit is removed, and new one connected to water line by squeezing spring-clips with a pair of flat nose pliers. Reconnect electric sensor.

Great move, easy, and saved myself the thick end of $200.

Washer would not drain.

  • Customer: Mike from Virginia Beach VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Removed three screws holding the cover, then one screw holding the pump assembly in place. After unplugging the power, it took two minutes to remove the clamp-rings from the hoses. The reverse was equally idiot-proof! But THIS "idiot" had 10-thumbs which added to the time to replace the lock rings! Added an extra 5 minutes at most! _grin_

replace motor

  • Customer: David from Eleva WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 5 of 7 people found this instruction helpful
Everything went great from order to done. Very happy

Door hinge had rusted out and was not closing properly

  • Customer: Sylvia from El Paso TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 5 of 7 people found this instruction helpful
We had to bread the hinge that had rusted out. That was the worst part. Putting the new hinge was no big deal. The time factor was also great. I called on Monday and had the part by Thursay. With a family of 6 a washer is a huge necessity.

Door would not open.

  • Customer: MIKE from LONGWOOD FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
It takes 2 people to do this repair.The bellow is the hardest part. One person has to hold the bellow in one spot, and the other person has to put it on the rim of the drum all the way around. Sort of like putting a tire on a bicycle. Dont do what I did and pry the door open. If you do that you will have to get a new door lock control at $54.Take off the lower front panel and reach up to the manual releace tab on the right side and pull down. Please make sure that the power is turned off, unplug the washer from the wall for your safety. The door switch itself is easy to replace, 3 screws, 3 plugs. Hope this helps.

knob broke

  • Customer: AMANDA from WEST PALM BEACH FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
replaced it

washer filled with water overnight

  • Customer: ROBERT from Millville NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
following the procedure was easy except the alignment of the new valve was off by 1/4 inch and I had to drill an additional hole to reuse the screw for attachment. Piece of cake otherwise.

baffle in tub fasteners broke, baffle disconnected from tub

  • Customer: Carl from Patterson CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
This part slides in and snaps in place, a 15 second job.

Front seal leaked

  • Customer: Ramon from Houston TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 11 people found this instruction helpful
It was so easy my wife replaced the part.

Old bellow pulled loose and torn

  • Customer: RICHARD from Portland OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
Was able to remove old bellow without dis-assembly. Replacement required removing the front of the machine for access. Once the front was off, the bellow was simple to replace. Biggest difficulty is getting the top mark on the bellow lined up. It has a tendency to slip out of position while you are working the back of the bellow over the retaining lip and it is not possible to rotate the bellow after it is installed. Fortunately, the tube from the detergent tray can be rotated slightly to allow for a small amount of error. Replacing the front retaining wire and spring required three hands at one point, but was otherwise not a problem. Fortunately removal and replacement of the front of the machine is pretty straight forward. I needed to disconnect wires to set the front out of the way, but it is impossible to plug them back in incorrectly.
All Instructions for the GHW9400PW0
61-75 of 310