Models > GHW9150PW0 > Instructions

GHW9150PW0 Whirlpool Washer - Instructions

All installation instructions for GHW9150PW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9150PW0
76-90 of 313
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer not drain or spin

  • Customer: LAURA from SPARTA KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 9 people found this instruction helpful
it was a really easy fix. unclamped the 2 hoses and took out screw, removed water pump. Connected two hoses back and set in place then screwed in locking screw. could not have been any easier.

The knob that controls the wash setting broke

  • Customer: Richard from Tempe AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
It only took a few seconds to slide on the new knob after it arrived by UPS. The part arrived sooner than scheduled. Great service and product.

The water didn't drain, so the drum wouldn't spin

  • Customer: Jill from New Rochelle NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
I took off the cover, removed one screw. Removed two hoses and the electrical connector. It only 5 minutes to replace the old pump with the new one.

Shaft in water pump broke

  • Customer: Jeffrey from Adrian MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 4 of 4 people found this instruction helpful
I removed the one screw that holds pun
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.

Displayed F and H alternately

  • Customer: LAVERNE from NIANTIC CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 7 people found this instruction helpful
Brother who used to sell appliances opened the washer door and read the booklet inside the washer telling him the part necessary to repair the problem. $33/00 for the water flow meter Part and shipped in next morning and arrived overnight. Excellent service for only $7.00 shipping. Highly recommend this place for parts. This was after a couple of days searching the internet for those with the same problem and not receiving and exact part to fix the problem

washer filled with water overnight

  • Customer: ROBERT from Millville NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
following the procedure was easy except the alignment of the new valve was off by 1/4 inch and I had to drill an additional hole to reuse the screw for attachment. Piece of cake otherwise.

Baffle was worn out/broken

  • Customer: Day from Basking Ridge NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
No instructions needed. Very easy to replace. You guys are great! Much cheaper than others and delivered next day! You are now on my "favorites"!

Pump not draining the water out.

  • Customer: Martin from Kotzebue AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.

FOLLOWING THE INSTRUCTIONS OF THE REPAIR MANUEL,

  • Customer: gerard from arvada CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
FIRST I REMOVED THE RETAINER RING AND THEN PULLED BACK ENOUGH OF THE BOOT TO GET THE DOOR SWITCH OUT AND PLUGGED IN THE NEW SWITCH PUT THE RETAINER RING BACK ON AND IT WAS FINISHED. WITH OUT THE REPAIR BOOK I WOULD HAVE BEEN LOST ON HOW TO DO THE JOB.

F-20 ERROR CODE

  • Customer: GARY from CLARKSVILLE IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 8 people found this instruction helpful
TAKE OFF TOP OF WASHER AND THE FLOWMETER IS IN THE BACK LEFTHAND CORNER ON THE TOP OF THE WASHER.REPLACED THE WATER LEVEL SWITCH ON THE TOP RIGHTHAND OF THE MACHINE ALSO. GOT ABOUT 150.00 TOTAL INVESTED W/SERVICE CALL FROM LOCAL TECH.F-20 HAS NOT CAME BACK YET. I HOPED IT FIXED IT WASHER IS ONLY 3 YRS. OLD. -GD

Pump not working

  • Customer: Darrell from Lady Lake FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Replaced pump

Control Knob Broke

  • Customer: Bill from Chanute KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
I removed the old control knob by pulling it off and installed the new one. Your service was great!

Front seal leaked

  • Customer: Ramon from Houston TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 12 people found this instruction helpful
It was so easy my wife replaced the part.

Would not pump water out at end of cycle.

  • Customer: Dennis from Huntingdon TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
First you need to remove the water from the machine, a shop vac hooked to the drain line works very well. Next remove the lower front panel ( two screws at bottom corners) and unplug pump. Remove the hose clamps and remove the hoses. Remove the screw at the front of the pump assembly and pull toward you and lift up. Instal new pump in reverse order.

Plastic door handle broke off

  • Customer: Lynn from Harrington Park NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
My 12 year old son did it in about 3 minutes. I wish I had oredered more because it is sure to break again.
All Instructions for the GHW9150PW0
76-90 of 313