Models > GHW9100LW1 > Instructions

GHW9100LW1 Whirlpool Washer - Instructions

All installation instructions for GHW9100LW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9100LW1
31-45 of 296
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Plastic Knob Cracked off machine

  • Customer: Susan from Glen Ellyn IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 18 people found this instruction helpful
It was super easy...as the knob (Part No. 18 on our Whirlpool Duet Dryer) broke off cleanly leaving the metal pin exposed....(we had been turning it with pilers in the interim) so I just popped the new knob on and we were good to go! It was really easy to do and easy to locate the necessary part on your site. I won't hesitate to use your company and website again. Thank you for making all the parts available and saving us a service call!

belt came off

  • Customer: wendy from Naples FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 18 of 27 people found this instruction helpful
Removed back panel,unscrewed the nut on the pulley.Removed pulley and belt. Reassembled.

Rubber Gasket (bellow) door seal "worn" out

  • Customer: Dan from Hudson WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 18 of 28 people found this instruction helpful
Have to remove the front two sections of the washer and top- I had to remove the control panel too. POS kenmore gasket failed after about 2.5-3 years. Old gasket got holes in it - If you have a HE3 or HE4 model- look for it! you will get them too!!! Guaranteed.

not pumping out the water

  • Customer: Dale from Ridgely MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 17 of 25 people found this instruction helpful
Disconnected 2 hoses and 1 screw and remove3d the old pump and reversed the proceedure to install the new pump.A piece of cake. Thanks

Bellow was ripped at the fold, leaking water into the casing.

  • Customer: david from Goose Creek SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 14 of 16 people found this instruction helpful
Removed the top panel. Removed the control panel (one screw behind the detergent drawer). Removed the three screws that held the door latch and switch (pushed it through). Removed the spring-loaded wire that fastens the boot to the door panel(look very closely around the bellow around the opening for the door). Removed the four screws at each corner of the front panel and removed the panel (door still intact). Loosened the band clamp that holds the bellow to the tub. Removed the vent tube from the old bellow and installed on the new bellow. Installation is the reverse of the removal. One tip: when installing the spring-loaded wire around the door panel opening, use several small (padded end) spring clamps to hold the wire in place as you install the wire. If you do not, the areas that you have installed will come undone. Be sure to be careful and use padded ends so that you lessen the likelihood of puching a hole in the new bellow.

Two problems- Error code FH, Water filling drum when washer off

  • Customer: William from Longwood FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 13 of 14 people found this instruction helpful
The Part Select website has some great information provided by customers. I search my error code problem that shut down the washer when filling and found the most likely scenario was a faulty flowmeter.
The other problem happening at the same time was the drum filling with water when the appliance was not in use. I thought the two problems were related, but upon further research decided that the most likely cause was a faulty water inlet valve.
I order the parts from Part Select and I could not believe how fast the shipping was. I just ordered regular ground but the parts got here in a couple of days.
The repair was easy. Remove four screws (need a star bit) from the top lid of the washer and remove the cover. The flowmeter and the water inlet valve sit right on top of the washer. Even with the lousy set of pliers I used, removing the clamps and disconnecting the hoses on both parts was easy off and easy back on. I had more trouble with the electrical leads on the water inlet, only because they were on so securely and I didn't want to rip out the wiring.
All together the repair for both parts took about 30 minutes.
Make sure you turn off the water supply and be ready to mop up a little excess water from the water supply lines when you disconnect them from the washer's water inlet valve.

shaking washer

  • Customer: Dean from Morrisville NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 20 of 35 people found this instruction helpful
twisted old shock absorbers out and snapped new one inplace...did not really fix my problem though

Drum didn't turn/spin

  • Customer: john from chester NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 17 of 27 people found this instruction helpful
1) Removed back of washer
2) Removed nut holding pulley
3) Pulled pulley off shaft
4) Put new pulley on shaft
5) Replaced and tightened nut
6) Replaced belt on pulley
7) Replaced back panel
7) Washed pile of laundry

FH code-4 minutes into cycle

  • Customer: robert from LITLE RIVER SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 12 of 13 people found this instruction helpful
remove 3 screws of top panel at rear. slide top to rear 1/2 inch and lift up. disconnect wire to flometer, remove clamps on hoses and remove, reverse to install. did not fix problem. ck'd screens at fill valves. ordered new fill valves--problem solved. solenoids must not have been opening up all the way.

Water leak through bellow next to the washer door

  • Customer: Jacek from San Diego CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 15 people found this instruction helpful
simple removal of few screws holding the washer panels and replacing bellow. 20 minutes to complete entire job. Kenmore mechanical washer design is very simple so all components access is very easy.

Worn out hose had a hole it it.

  • Customer: Edward from Clinton MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 13 of 18 people found this instruction helpful
I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.

Washer would not spin ( F-02 comes on)

  • Customer: Steve from Dubuque IA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 11 of 13 people found this instruction helpful
1-Unplug washer
2-Remove the bottom of the front washer cover 3 screws
3-Locate pump and loosen pump drain cover turn to left just a little enough for water to start draining.
4- Suck-up water with wet/ dry vac. Remove 1 screw holding pump.
5- Flip pump electrical cover up and disconnect wiring from pump.
6- Remove 2 hose clamps. The outlet was not to hard to remove, but the intake was not easy to get the pliers on.
7- Install new pump. See instruction to install. I didn't have to remove any ribs to install the connector as in the instruction sheet that came with the new pump. Also I didn't think it was very clear instruction.
8- Last installing the spring clamps. The outlet went okay, but the inlet I never could get on. I could not get the pliers on the clamp. I fooled around at least 20 min. trying to get the clamp on. I went out and bought a 3/4 to 1 3/4 stainless hose clamp with the worm drive design. That is what took so long.You may want to get new hose clamps before starting.
Other wise I did okay.

would not spin of agitate

  • Customer: Doug from Hartselle AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 13 of 19 people found this instruction helpful
I first had to take off the back and the top to get to the pulley and the belt. The pulley had woobled so much that it had worn out the center nad it would no longer hold to the post in the tub. It also had cut into the back of the tub about a 1/4 to 1/2 inch. I unscrewed the nut holding the pulley and removed it. I then took a knife and trimmed the rough edges off the back of the tub to make it smooth. I then smoothed out the end of the post that the pulley fits on so the new pulley would fit. I tightned the nut and put the belt on the motor drive shaft and Used a robo grip to hold the belt as I turned it onto the pulley. I but the back and top back on and that was it.

leak suddenly developed

  • Customer: Gerald from Troy NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 11 of 13 people found this instruction helpful
Somehow a bobby pin got into the drain pump housing. When it started to drain, the pin was rammed through the housing.Extremely easy to remove and replace. No special skills needed. Whirlpool did a good job in making it idiot proof. Unpacking the part took longer than installing it. Don't be afraid to do this repair. If you own a pair of pliers and a screwdriver,you can do it.

Door would not lock

  • Customer: Tina from petersburg VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 14 people found this instruction helpful
Peel rubber gasket from drum; remove 3 screws using phillip head screwdriver; disconnect wiring e plugs; remove door lock. Install in reverse order.
All Instructions for the GHW9100LW1
31-45 of 296