Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice buildup. The Ice Machine was frosting over. Ice (due to frosting) would block the drop chute.
Unfortunately, the replacement part didn't come with instructions. The repair, nevertheless, was fairly straightforward. After removing the plastic parts that guide the ice through the door (by removing a few screws that attach the parts to the inside of the door), I was able to slip my hand into the ice maker dispenser and remove the old part. The part clips on. It is a tight fit through the funnel (from the outside of the freezer), however, and requires that the gasket first be "flipped" open wherein it unfolds 180 degrees. Doing this will make it easier to clip the new gasket onto the assembly.
Just had to pull ice maker drawer out and replace the drive cup which was very simple. Light bulb on door dispenser was kind of hard to get back in cause it is such a small space to screw the bulb in.
The repaire guy came in tooke it out and told me it is goin to coast $20 for the part and $50 for the labor..... So I looked, It was soooo eeezzz ALL you have to do is get the switch out( with help of my butter knife :) it plugs in to a little outlet on the wire (on the botom side) so take out the old one and plug in the new one wich I got for $8 + $6 shipping = $15 THANK YOU PART SELECT for saving me $55 Im a 36 y/o stayathome mom and Ihave never don this before, Im very proud of my self. well... it was very easy!
turned out to be a rusty drain pan in the refrigerator section behind the fan fixture attached to the wall.I followed the instructions of a prior customer on the website and it worked like a charm. Super happy to have done it myself!! Can't believe they don't use plastic for this part as it would rust again if I didn't coat it with the rustproofing spray.
Groove for retainer clip on auger nut was broken out.
After removing three screws on the ice bucket, it basicly came apart by itself. I needed to use pliers to remove the old nut because it had over tightened itself onto the shaft. Be careful here - it is a left hand nut - not a normal right hand nut! Reassembly was a snap putting the parts back together in reverse order. Unit has been working great since the repair.
the drive cup on the auger had broken in half, no ice dispensed
Removed four screws holding the bin ontomain body. lifted the auger enough to slip in the new cup and placed the bin into the main body and installed the four screws back. Put the bin back into the Freezer. it work just fine
This is the second or third time this cup has broken. Maybe we use more crushed ice than the average family, but you would think this part could be more durable. Anyway, I digress. This is about the repair. Four screws removed around bottom of tray, one screw removed for some bar that mechanically opens a door to allow ice to fall out of the tray, and two butter knives used to release tabs around the screw components... and we were done.
Light switch shorting out causing open door alarm to go off
Easy fix, but they don't give you plenty of wire to work with. When I pulled the switch out it only had about an inch of wire that came with it. meaning if I didn't have a grasp on the wires as I was removing the switch they would have slipped back up the opening
broken tine on stripper left one cube to jam the ice maker
There were no fastening hardware. The plastic stripper just snaps in place. I had to be patient and could not get it out until I put upward pressure on the stripper.
Ice maker would not dispense ice, crushed or whole.
Removed the ice maker from the freezer. Unscrewed the outer cover/base of the ice maker. Unscrewed the long lever that opens the ice chute. This freed up the feeder coil enough to pull it out enough to replace the cup drive. Once I replaced the cup drive, I laid it back down into the ice maker bin, reattached all the screws and it worked! The old cup drive had a tine broken off which would not allow the feeder coil to turn. It seems like a weak part and I anticipate I may have to replace it again in a few years.
Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!
Replaced both temp sensors worked good for 2 days then began freezing food. Looked into it further on line. Found small motorized door broken that controls the cold air from the freezer
Plastic piece that holds up motor that pushes out ice cubes broke off from bucket glide
Took out ice tray and then slid motor out of right side bracket and sat on shelf. Removed the 3 screws holding up left side bucket glide first. Make sure you have correct size socket for the 3 screws on bucket glide. Works best with a screwdriver type socket tool. I then removed broken plastic piece from motor (screw in motor is different size than the ones for left side bucket glide). I put in new left side bucket glide (rear back screw a little bit of a challenge but it can be done) and then slid motor back into right side bracket and fastened motor to new plastic piece that sticks out from left side bucket glide. Put back in ice tray and good to go!