GHD4309N10CS General Electric Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No water able to come in or out.
Repair is super easy and anyone can do it in no time!
At first my fear was that it was the pump, but after reading through the trouble shooting here it narrowed it down to the water inlet valve. The new valve even came with easy to read and understand instructions. I had it fixed in less time than it took my wife to make us lunch lol.
2 screws hold the mount bracket in place. Just remove the screws, remove the c-clip that holds the secondary/small water line on, pop the hose off then remove the main water inlet line [ its the bigger line with the brass fitting ] I only needed a pair of pliers for this. Reinstall the main water line into the new valve, but make sure you use pipe tape on the fitting or you'll have a water leak. Reinstall the secondary water line and reclip the c-clip using pliers to squeeze the clip. Hold the valve in place and reinstall the 2 mounting screws. That's it your done !!
This is the second time I've used partselect, and they are hands down the best !! Other sites would have you buying part after part until you happened to get lucky and get the right one. Not here, they help you figure out just what you need and nothing more.
Great people and fast service !!
Thank you once again.
At first my fear was that it was the pump, but after reading through the trouble shooting here it narrowed it down to the water inlet valve. The new valve even came with easy to read and understand instructions. I had it fixed in less time than it took my wife to make us lunch lol.
2 screws hold the mount bracket in place. Just remove the screws, remove the c-clip that holds the secondary/small water line on, pop the hose off then remove the main water inlet line [ its the bigger line with the brass fitting ] I only needed a pair of pliers for this. Reinstall the main water line into the new valve, but make sure you use pipe tape on the fitting or you'll have a water leak. Reinstall the secondary water line and reclip the c-clip using pliers to squeeze the clip. Hold the valve in place and reinstall the 2 mounting screws. That's it your done !!
This is the second time I've used partselect, and they are hands down the best !! Other sites would have you buying part after part until you happened to get lucky and get the right one. Not here, they help you figure out just what you need and nothing more.
Great people and fast service !!
Thank you once again.
Parts Used:
-
Victor from Raymond, NH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Wrench (Adjustable)
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rack slide end cap missing
installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy
wife happy
Parts Used:
-
Carrell from Cochranville, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old part leaked
unscrewed dishwasher from cabinet, then I flipped dishwasher on it's side. loosen pump motor bracket arm on the end of the motor. loosen pump motor to pump conecter hose clamp and then unscrewed pump motor connector from dishwasher. To install I did the reverse. very easy.
Parts Used:
-
robert from east windsor, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken original part
Took 5 minutes. Snap the old part off and replace with the new part. No problem.
Parts Used:
-
Stan from Westminster, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
latch on detergent assembly broken off
Easy repair-removed hex nuts and and screws to pop out old part and replace with new one. New part works better than the original! 1st replacement part arrived with a broken piece, a quick, courteous phone call got a replacement sent out. It took a 2nd phone call to obtain the refund, but the customer care reps are efficient and friendly. I would order from them again for positive service reasons alone.
Parts Used:
-
Carri from Louisville, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper rack kept dropping from the wheels when we pulled it out
We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.
The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.
The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.
Parts Used:
-
Joel from Cypress, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drain pipe was missing when purchased used dishwasher
-
arthur from ALMENA, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Three of the 8 wheels broke.
The newly purchased wheels have a little different design and could be installed in a matter of few seconds.
Parts Used:
-
Asok from HELOTES, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel had melted and support cracked
Removed the lower rack and installed new wheels with clips
Parts Used:
-
Tom from UPPR CHICHSTR, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
It makes a beeping sound in the middle of the dishwashing.
Remove the screws from the door and replace the switch interlock and door latch.
The problem is fixed and the dishwasher works fine so far (about three weeks) now.
The source of the problem looks more like the door latch because I use to push the door in to get it going before I replace the parts.
The video I received via email that show the how to do it was very helpful.
————-
Update after more than month. (12/30/2020)
The problem still persists. However I have a possible solution for it that doesn’t require any parts at all. The entire dishwasher is tilted backward. As the washing started and the water pileup in the bottoms of the dishwasher, it pull the entire dishwasher back work causing the switch interlock to release (open the relay causing the door open been sounds).
Level the dishwasher so that it doesn’t tilt backwards and this should fix the issue. I will post the latest after a month. If you need more info I can send a picture to describe the issue more clearly.
—————————
Update 01-06-2021
The problem still persists. The above theory I had was wrong and didn’t make any difference.
However, I have a permanent solution but it may not be ideal for most people ??. The relay that get close/open when the door is close/open is now always CLOSED. To start the dishwasher just press start and make sure you don’t open the door while the dishwasher is running. It will not stop. I am sorry and I know it’s not a good solution but it’s kind of funny.
The problem is fixed and the dishwasher works fine so far (about three weeks) now.
The source of the problem looks more like the door latch because I use to push the door in to get it going before I replace the parts.
The video I received via email that show the how to do it was very helpful.
————-
Update after more than month. (12/30/2020)
The problem still persists. However I have a possible solution for it that doesn’t require any parts at all. The entire dishwasher is tilted backward. As the washing started and the water pileup in the bottoms of the dishwasher, it pull the entire dishwasher back work causing the switch interlock to release (open the relay causing the door open been sounds).
Level the dishwasher so that it doesn’t tilt backwards and this should fix the issue. I will post the latest after a month. If you need more info I can send a picture to describe the issue more clearly.
—————————
Update 01-06-2021
The problem still persists. The above theory I had was wrong and didn’t make any difference.
However, I have a permanent solution but it may not be ideal for most people ??. The relay that get close/open when the door is close/open is now always CLOSED. To start the dishwasher just press start and make sure you don’t open the door while the dishwasher is running. It will not stop. I am sorry and I know it’s not a good solution but it’s kind of funny.
Parts Used:
-
ANTENEH B from EAST GRANBY, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would NOT drain
-
Nathaniel from HAWKINSVILLE, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not cycle from "wash", just kept running
As per instructions, any one that can read and use basic hand tools could do it. Very nice color instructions. BTW, this was an excellent value, $20 cheaper than two of the other parts houses I checked. Super fast shipping
Parts Used:
-
Mark from Burton, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mouse Ate Pump Inlet Cover,
Removed dishwasher from counter tiped it over and replace the inlet cover removed the back of the front door and replaced the switches
Parts Used:
-
Robert from Belford, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
5 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
at start of the wash cycle did not take in any water
very easy old part out new part in direct replacement, fit right in and it is working. Great deal and about half of the price than ge website. Thank you.
Parts Used:
-
wojciech from bayonne, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
5 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The water inlet valve on the dishwasher leaked.
The repair was very easy and straight forward. I removed the electrical wires, removed the two hose's and then removed the old valve from the dishwasher frame. To install the new valve, I just did everything in reverse. No problem and I saved about $80 for the repairman to come out and I am sure I would have paid more for the valve if he provided it.
Thank you.
Thank you.
Parts Used:
-
John from Andover, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench set
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!