Models > GEW9250PW0 > Instructions

GEW9250PW0 Whirlpool Dryer - Instructions

All installation instructions for GEW9250PW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GEW9250PW0
526-540 of 589
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer stopped heating

  • Customer: Daniel from Palmyra VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Using information found on this site, I was able to quickly locate the two bolts on the lower front panel of the dryer to get at the heating element. Once I removed the panel, I was able to use a multi-meter to determine that the heating element was the issue as the resistance reading was infinite opposed to the expected 10 ohms. When the replacement part arrived, I then re-accessed the heating element to remove it. I removed two bolts from the front deflector to gain access to the heating element (after opening the lower panel) and also removed a third bolt that held the heating element in. Once those were removed, I was able to remove the old heating element which was indeed bad as the wire was broken. I did find that it took a little effort to remove the old heating element. It was quite firmly placed in its location however once I put enough effort into it, it came out quite nicely and the replacement element went in quickly.

Broken door catch

  • Customer: Chuck from Bozeman MT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two small screws on door edge, pop out broken part, insert new part, replace screws. Took 2 minutes 18 seconds. Nice to have various door catches in the Kit. This was a repair on a 1979 Whirlpool Dryer. Great price & service!!

Dryer was not heating up

  • Customer: Lynn from Spencer IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I watched a fix it video and than just followed what it said to do. My husband was very impressed and it saved us a lot of money. I had my dryer running in no time. Parts came very quickly after I ordered them. Thank you

Squeak and Rachet type noise

  • Customer: Brian from Mertztown PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
The videos really make it easy. I put my laptop on the washer next to my dryer and proceeded step by step. I also found the video that mentioned about the screws that may come loose on the baffles. I found several loose screws on the baffles which I tightened and I also found the Drum hole plug loose, so I also tightened the plug. Reassembled the unit and has been working like new since.

old idler pulley was worn out

  • Customer: David J from Eagar AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Simply slid new idler wheel on then popped thr tri ring on. The belt replacment was the hardest thing which was also easy. I think pulling the dryer away from the wall was the most difficult thing.

Needed to vent to side due to space requirements

  • Customer: Harlon from Browns Summit NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Upon receipt of the new vent kit, I removed the dryer from its location and took it in to the garage. This facilitated a roomier work space. The directions were easy to follow and the work to be performed was very easy in this setting.

Tumbles but no heat

  • Customer: Danny from Niagara Falls NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Tested sensors for opens and resistance found Thermo. fuse had open (NO CONTINUITY )order new Thermo Fuse was wary about resistance on Internal Bias Thermistor.Replaced both and problem was solved .Piece of cake if you are familiar with a Multi. Meter other wise it would be a guessing gam

Dryer stopped tumbling during a cycle, would not tumble afterward

  • Customer: Jennifer from tallahassee FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Extremely easy! you can do this too. Just watch the video and have the few basic tools the video suggests. I am not skilled in repair at all. This part was shipped very fast and everything I needed was on the site. The hardest part was cleaning up the lint, seriously. Don't spend $100+ for a repair person to come to your home. This task is simple for anyone, any skill level.

no heat ,burner not turning on

  • Customer: Donald from Orchard Park NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
unplug unit ,remove back cover six screws, slide off two wires on thermal fuse, remove one screw remove and replace fuse, reattach wires replace back cover

The Drier started making an unusual noise, then stoped in the middle of the cycle. I attempted to start it again after a while and it did start to stop again after a few minutes.

  • Customer: Armando from Sterterling Heights MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
This appliance is 14 years old. I debated whether or not if worth to be repaired. I decided to repair it since a new one of comparable model is about $600. Firts, Disconnect the appliance. Remove the control panel side covers and unscrew the screws in the bottom, (one on each side) Flip the control panel up. Now you have access to the 3 screws that hold the drier top on place. Remove the 3 screws and slide the panel towards you and lift standing on the front of the appliance. Set the top aside. The fron bottom panel is attached with two clips on top and hinges on two bottom clips. With a potty knife or flat screw press in each top clips and pulls the cover towards you and lift that will removed the cover. Next, un screw the two screws in the bottom of the top front panel. Disconect the wires of the close door switch. I usially take a picture of the connections before discconnecting anything so I can use as reference when putting it all together again. Remove the two top screws. Remove the spring of the door (two, one on each side), remove the lint trap. Be careful if you open the door after you remove the springs and make sure whne you close the door is snaped in the close position. Remove the front top panel. Next, remove the blower cover (two screws on the front of it, Remove the blower ring ( two screws) Remove the belt by pushing down the spring loaded pulley and sliding the belp to the side. Grabing the tub by the belt carfully lift it and slide it out from the drier enclosure. Using a 1/2 in socket wrench place it in the center of the blower and hold the motor shaft at the other end by the pulley using adjustable wrench. Unscrew and remove the blower. Remove the back cover of the blower (4 screws) Discconnect the motor harness and unclip the two clips holding the motor to the mount bracket. Remove the motor and replace with the new one. Follow these instructions in revers order. It was very easy and my drier is working great now. I inspected the belt and pulleys and lubricared all moving components and of course cleaned and vacum all debry and lint. I hope these instructions help you and good luck :)

Dryer door would not close and latch on both catches w/o pushing them shut individually.

  • Customer: David from Middleton WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Our make/model was not on the online instruction, but it was similar. Ours had a glass (plastic)front window in the door. To remove the top catch you had to take out the top four screws that hold the door together (philips head screws) allowing you to pull back the gray plastic strip to access the top latch, then replace it like in the online directions using a needle nose pliers. The bottom catch, once the two remaining the screws were out gives you access to the bottom catch. Remove it with the pliers and snap the new ones into place. You can completely take out the window when you replace the bottom latch if you want.

door wasn't shutting

  • Customer: Tom from Crystal Lake IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Just pulled the old parts out on door latch and put the new ones in. Thanks Parts Select for your prompt response and easy process for order and shipment.

broken control knob on dryer

  • Customer: Diane from Suwanee GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Husband out of town, house full of company (all women) and the dryer breaks. Yikes! Your company got the part to me so very quickly, I replaced the knob in minutes and all the women got to do their laundry. Happy happy group. Thanks!!!!

Damaged motor, worn out belt and wheels

  • Customer: Louis from Miami FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
We obtained the parts diagram in PDF format, which made disassembly very easy. We then ordered the parts and thanks to the promptness in delivery and knowing how to diassemble the dryer, we replaced the broken parts quickly and without having to call the repairman.

No heat dryer just tumbles and blows cold air

  • Customer: jo-co from warrensburg MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Easy to follow videos on your site made this repair a breeze. I ended up having to replace the high temp cutoff as well but for 60 bux my dryer works like new. The repair man wanted $100 just to come look at it. Could not have done of without the easy to follow video.
All Instructions for the GEW9250PW0
526-540 of 589