Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GEW9250PW0 > Instructions

GEW9250PW0 Whirlpool Dryer - Instructions

All installation instructions for GEW9250PW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GEW9250PW0
556-570 of 597
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Quit running after one to five minutes - consistently

  • Customer: Walton from Leesburg, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the repair tests followed in repairman's sheet found taped behind front lower panel. When into diagnostic mode (found on paper) and tested the top front control panel buttons. All checked out fine except when I opened the door it beeped and showed a 4E code. So per the paper Tested the Moisture sensors (two metal strips inside of dryer where lint screen is) test passed, only three things left for this issue per the manual. Wire harness from two metal strips, longer wires going up from that harness to electronic control board , and the ECB itself(found under top lid of dryer). Since did not have a meter, Replaced the lower wire harness first - no improvement. replaced ECB - works perfectly now. Saved $$$ vs a new dryer.

Lint Screen Deteriorated

  • Customer: Robert from Ingram, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced Lint Screen

Dryer would not start

  • Customer: steve from hot springs, SD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced Thermal Fuse

Dryer would not start when I hit the start button

  • Customer: Sue from Valencia, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Your website was wonderful--thank you so much! When I saw that 47% of the time this was the problem, I ordered it & it worked! This was a life saver for me! I will come back to this site anytime I have an appliance problem! Thanks again!

no heat

  • Customer: Larry from Buckhannon, WV
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
very easy had to do some rewirng.who ever had it before me bypassed the fuse and several other things.

Door Latch Would Not Hold Door Shut

  • Customer: Marion from Farwell, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took screwdriver popped out old latch in cabnet. Took pliers popped out latch out of door. Snaped new latch parts back in.

No heat

  • Customer: bruce from florence, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed rear panel screws carefully removed panel with out disconnecting wire harness located thermal fuse removed 2 screws removed the 2 wires with needle nose pliers put new thermal fuse in connected the 2 wires carefully put panel back on and tightened screws turned on power and start got heat problem fixed

No heat on any cycle

  • Customer: ERIC from DAYTON, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Had previously replaced the heater coil (purchased from PartSelect) and fixed the no heat problem. Should have taken advice given on this site and replace the thermostat and thermal fuse kit at that time. Since I knew how to remove the assembly it was easier this time. Just remove, unscrew the two parts and replace with the new ones. Reattach the wires and reinstall the assembly and it is now working again. Also vacumed the inside and trimed and replaced the exhast vent hookup for less restriction.

bellow ripped

  • Customer: Sheila from Tucson, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After trying to follow a very detailed description by another consumer, we googled our washer and found a site that showed step by step direction that took us through removing all panels and getting to the bellow easily. Not removing the proper panels, we found was making the job hard!I believe the site was applicance services...very helpful! Step by step literally!!Cost of parts through parts select reasonable.

Dryer's start button would not work

  • Customer: Terry from Lolo, MT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I diagnosed the problem using the web page. It said that 60% of the people with my problem bought the Thermal Fuse. I unplugged the dryer AND cut the power at the fuse box. I used a screwdriver to remove the vent hose, a nutdriver to remove the back of the machine. The thermal fuse was right there. Removed the old one with a screwdriver, unplugged the wires from the old one and snapped on new one, and screwed it back in. Re-installed the back of the dryer and the vent hose and Whoila! It works like a champ.

needed new lint filter

  • Customer: Warren from Cedar Falls, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
pulled out old lint filter. Put in new lint filter.

Dryer door wouldn't close.

  • Customer: John from Mountain Top, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Repair was very easy simply used a screwdriver to remove the cracked old latch and used my fingers to insert my new latch.

Dryer will run, but will not heat

  • Customer: William from San Jose, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Preface this by saying I'm not a good handyman. I love working with my hands, but I cannot cut straight, make angles, plumb, or do anything electric. I knew I had a gas dryer but I had to learn that it uses a burner not a coil. That said, armed with my trusty iPad, I located Part Select, watched a video or two, entered my problems into the correct fields, and made an educated guess based off of the results. Since I already had the front cover and the motor cover off the dryer and the 2 sensors were right there, I ordered both-why take the chance. I ordered Sunday evening and the parts arrived Tuesday around noon. By 1pm I was drying clothes. Feeling pretty cocky now, I'm going to try to hang gutters this weekend.

One was missing

  • Customer: Keith W. from Rushville, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Popped the panel open & replaced the one that was missing with a new one!

Dryer not heating

  • Customer: Matthew from Italy, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
1) Unplug dryer from wall. 2) Remove bottom panel on front of dryer below door. There are 2 screws. You will need a 1/4" nut driver. 3) Remove 2 screws (same size) holding the clip in place at the front of the element housing. Then remove clip. 4) Pull housing and element forward. Will take some twisting and angling to get it out. 5) Make a diagram showing which wires go to what terminals. Then pull wires from terminals. (Now would be a good time to remove lint and trash or in my case that bank card I lost last year from bottom of dryer.) 6) Remove screw holding coil inside housing and pull coil from housing. Use pliers and some muscle. 7) Install new coil and replace wires, housing, and panel doing this process in reverse. For internal bias thermistor, while front panel is off, find the part inside. It is toward the center near the front of the dryer. There are 2 wires and 2 screws 1/4" hex heads. Remove wires, remove screws, and replace.
All Instructions for the GEW9250PW0
556-570 of 597