All Installation Instructions for General Electric Refrigerator GBSC3HBXCRBB

The old veg. pan was chipping along the track and was difficult to get in and out

The new pan arrived within two days, but, als, it was cracked also. I called immediately and with no fuss I was promised another pan. It arrived in perfect condition the next day. Count me as a satisfied customer.

Parts Used:

Refrigerator Crisper Drawer

Patrick from Fairfax, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

sticky switch

easy pry out, disconnect wiring, connect on new switch and press in switch.

Parts Used:

Light Switch

ANTHONY from NEW EGYPT, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Rat chewed up fan blades in refrigerator at our camp.

We just pried off the fan blades and pushed on the new part. Could not have been easier. The rat has been permanently dipatched and, hopefully, that is that.

Parts Used:

BLADE CONF FAN Assembly

Compression Ring

Wendell from Baton Rouge, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

broken slide drawer track

Took out shelf, unscrewed old track, screwed on new track. Only thing is not a standard flat or Phillips screw head so if you don't have a star head bit, you are out of luck.

Parts Used:

Drawer Slide Rail - Right Side

TREVOR from KENT, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set

Was this instruction helpful to you?

Thank you for voting!

The plastic piece that holds the screw in on the pan of the refrigerator had broken

I took the pan out, replaced the bar with the new part - slide pan RH - and I was back in business. It couldn't have been easier.

Parts Used:

Drawer Slide Rail - Right Side

Kathleen from Burke, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

no lights in frig

killed power-gently pried out old switch using two screw drivers-replaced faulty switch-and tested OK.

Parts Used:

SWITCH LIGHT FZ

brian from coral springs, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

broken fan blade

about an hour to figure out what was causing the vibration and noise and about an hour to put it back together and 5 min. to order a new fan blade thank you.It started making noise during thanksgiving dinner so we toke it apart after dinner and I cut the other 2 blade to match the broken one so to cut down on the noise and vibration semi put it back together and 7 days later the part arrived.

Parts Used:

EVAPORATOR FAN BLADE

Dan from Seattle, WA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

broken slide pan lh

pull out the slide pan lh and replace for the part

Parts Used:

SLIDE PAN Left Hand

Aaron from Montebello, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Ice dispnser worked intermitently. My diagnosis led me to the freezer door light switch. Switch operated the light but stopped the ice dispenser. After replacing the switch the dispenser operates every time now. problem solved.

Little difficult getting the switch out, had to pry wth some force. New installation was real easy.

Parts Used:

SWITCH LIGHT FZ

Jeffrey from Poestenkill, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

failed light switch

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

Parts Used:

Light Switch

Jules from Crowley, LA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

The two drawers were hard to pull out so we broke the plastic on the runners.

The replacement drawers went in very easily and we are so pleased.

Parts Used:

Refrigerator Crisper Drawer

Judith from Tewksbury, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

no light in freezer

Connected the 2 wires and pushed in the switch until it clicked.

Parts Used:

Light Switch

christopher from collegeville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

refig light did not work

per your instructions

Parts Used:

Light Switch

paul from east hanover, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

switch wouldn't come out anymore and turn light on

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

Parts Used:

Light Switch