G3267XRW-4 Maytag Range - Instructions

unscrewed old burner head ;disconnected 2 wires; repaced with new burner head and replaced wires. Unfortunately, before we really needed to replace the other burner heads, the cooktop itself developed a gas leak. We decided to replace the whole thing, and therefore would like to return the unboxed, unused 4 remaining burner heads.

removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.

It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.

First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I turned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !

It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison

Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.

My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.

Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.

First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.

I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.

The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to fully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.

ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job