Models > FFU14FC4AW0 > Instructions

FFU14FC4AW0 Frigidaire Freezer - Instructions

All installation instructions for FFU14FC4AW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the freezer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FFU14FC4AW0
16-30 of 70
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Freezer wouln't start

  • Customer: Ivette from Grand Island NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
First I removed the clamp, pulled out the part, and diconnected the two wires on the side and a small screw. Reconnected the new part with the small screw, connected the wires and plugged the part back to the side of the motor. Whaa La, Done.

Lost Locked Freezer Door Key

  • Customer: Robert from San Rafael CA
  • Difficulty: Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Had to drag the full freezer out from the wall to expose the name plate, got the Model # and S/N and found the key on the partselect website in minutes. It was cheap so I got two. Other than FEDEX not knowing my address correctly, when I finally got the key it worked fine. Not a problem anymore.
Thanks

MY FREEZER WAS FROSTING UP, MY ICE MAKER WAS NOT WORKING ,AND MY FRIDGE WAS WARM.

  • Customer: Todd from Kewaskum WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
HAD TO REMOVE ALL SCREWS ON REAR BACK COVER OF FREEZER INSIDE, UNPLUGGED REFRIDGERATOR, UNCLIPED THERMOSTAT, UNPLUGED THERMOSTAT. REPLACED THERMOSTAT WITH NEW ONE IN THE SAME LOCATION, AND LET DEFROST FULLEY. REASSEMBLED, PLUGED IN, AND TESTED. ALL WAS GOOD. BUT I DID ALSO REPLACE TIMER AT FIRST PART OF THE REPAIR SO I SUGGEST YOU REPLACE BOTH AT THE SAME TIME.

Freezer fine, fridge too hot!

  • Customer: Marc from Chesterfield MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
Removed the back panel in freezer compartment with the nut-driver. Then I cut off old thermostat connections, and spliced in new thermostat connections (repairman had already replaced defrost timer, and said not to trust connectors included on wires-they failed often). Then I snapped thermostat itself onto cooler coil. So far so good, fridge is running at 35-40 degrees a week later. Thanks Parts-Select!!!

Kids broke the handle somehow on the garage freezer

  • Customer: Geneva from Murrieta CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
By simply popping off the handle cover the two screws were revealed which attach the handle to the door. New handle fit exactly like the old one. Easy peezzy lemon squeezy.

Cooling coils would ice up and fridge would warm up

  • Customer: Richard from Tehachapi CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
I removed the shelves in the freezer, took out the five 1/4" screws and lifted off the cover. It was a simple matter of using a blow drier to remove all the ice, then unplugging the two wires and unclipping the thermostat from the upper cooling tube. Then clipped the new one on and reconnecting the two wires.

Works great!!!

Freezer frozen, refrigerator warm

  • Customer: Janet from Stockbridge MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
removed the screws/nuts; pulled the back panel off, removed the old thermostat (wires just popped apart) replaced the new thermostat (wires just popped back on) replaced the back panel and the nuts and TaDa!!

door handle broke after years of use

  • Customer: christine from gloucester MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I ordered the handle , which was easy and resonable priced.
I used a cordless screw driver . And it was done in under 30 seconds . Quick repair

The door handle broke off of the freezer.

  • Customer: Stephanie from Irving TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 6 people found this instruction helpful
The repair was really easy - I used a phillips head screw driver to remove the screws and broken pieces of the handle, screwed the new one on and snapped the handle insert into place. I was thrilled to be able to find the parts so easily (the information you have online is really helpful!), the parts arrived much faster than I anticipated and the handle was easily replaced! Thank you!

Freezer was freezing solid

  • Customer: Matt from Cincinnati OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 2 of 3 people found this instruction helpful
I first replaced the defrost timer about a week prior and it did not correct the problem. I then ordered the thermostat from partselect and within 15 minutes had the part installed. My refridgerator has been running correctly for a couple weeks.

defrost thermostat was open most of the time and didn't let the defrost element heat up.

  • Customer: Elvin from Gardner KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 4 people found this instruction helpful
Removed evaporator cover, unplug 2 wires to thermostat, unclipped it from the coil. Installed new themostat back the same way.

door handle replaced

  • Customer: Thomas J. from Madison Heights MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Old handle was off already. Took the to screws from old handle, put the new one on screwed it on and that did it.

shut freezer-vacuum pump made hard to reopen-wife broke handle in tugging.

  • Customer: mike from longview TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
first removed two screws that held handle. Then replaced. Ordered a motor 3 years ago from land office with verbal over counter instructions and that was easier but to get part this time was very simple ! With the model number and name brand input on site I had part in 3 days instead of waiting for a chance to visit land store and HOPE they had the part. Y'all might consider a zoom feature for us older folks.

Broken handle

  • Customer: Bill from Elmira NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I was surprised that the screws and trim piece were not included so make sure you have them from the old handle or order new. First removed the broken ends still on the freezer. I removed the small metal brackets from the old handle and put them on the new one, screwed the handle to the freezer and put the trim piece on. Real easy.

Just lost key

  • Customer: Toni from Little Rock AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
No repair. The key fit!
All Instructions for the FFU14FC4AW0
16-30 of 70