Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Heating element went out
Removed the clamp holding it to the floor and removed the c-clips holding element underneath and put new one in. Hard part was figuring out what was holding the element but since I still had the schematic drawing we figured it out. Saved a bunch on a repairman. After watching my friend install the new element I could probably do it myself next time.
FRIDGEADAIRE - GALAXY SERIES -Part arrived within 3 days of order BUT it was wrong part. All excited about getting the upper wash rack in full operation once again. Pilled shelf out to remove gasket to find it looked nothing like the one on there. The part I need is like a bellows of sorts that fits on the water line attached to the upper shelf. The part received goes on the back wall. Now i am back at square one with part I don't need and hoping for the part I do need
Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.
Removed the bottom covering on dishwasher and then ran it to figure out where the leak was coming from. Noticed it was dripping off hose, but not actually leaking from hose.
Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)
Followed delivery tube up side of dishwasher to top of tub and noticed reminents of where water ran down side of tub.
Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.
Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks
Dishwasher was not filling up at the start of the cycle.
This was really easy. Have done it before on other older dishwashers in the past. Turned off the breaker for the dishwasher. Turned off the water supply valve. Unscrewed the screws in the panel that hides the parts under the dishwasher. Unscrewed the screws anchoring the dishwasher to the counter. Slid the dishwasher out about a foot. Inlet valve was located on the front left side of the dishwasher. Unclipped the wire harness. Placed a cookie sheet under the water line. Unscrewed the water line from the inlet valve. Unscrewed the two Phillips head screws holding the valve to the dishwasher frame. Got the new part. Put the screws back into the frame. Reconnected the water line and wire harness. Slid the washer back into place. Turned on the water valve. Watched for leaks. Turned the breaker back on and started the cycle. Watched for leaks. Once I saw there weren’t any replaced the screws anchoring it to the counter and replaced the cover on the bottom. That was it! Took me longer to type out the steps than it did to actually do the repair.
I closed on a house a few weeks back. You really don't notice issues with appliances until your living there....the walk through doesn't give you the time to really see anything hidden. Anyway - the dishwasher had appeared to be used to wash grease covered parts from a car so I pulled all the racks and filters out and placed the order for replacement parts. I saved hundreds in obtaining replacement parts verse buying a new machine - and I didn't have to sit around waiting for a repairman to do the work for me. I've made several purchases from PartSelect, and will probably making more in the near futre - Thanks!
First I removed the bottom dish rack to gain access to the spray arm. I proceeded by pulling straight up on the bottom spray arm, it disconnected with gentle force. The replacement part was not identical, so I determined that it would work by inspecting hole patterns and heat shield configuration. Then I gently pushed the new spray arm onto the water supply tube making sure that the spray arm snapped into place. Due to extremely fast ground shipping (less than 20hrs from order to my door) the repair was done within 24 hrs! Boy...was my wife pleased!
took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.
For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it with silicone caulk, but may have to replace that - looks easy, .
First I removed the six Phillips head screws that hold the control panel on. Next I removed the two Phillips screws holding the door latch in place. Then attached the new latch and reversed the procedure. Best part was the prompt delivery of the new part. My wife had herself convinced she would be without her dishwasher for several days.
I researched the problem we had with our dishwasher and found the Parts Select website. My husband and I figured out how to remove the broken part and I selected and purchased the replacement.
The part was shipped quickly and when it arrived I changed the broken part with the replacement in less than five minutes. It seems to be working just fine.
I have added Parts Select to our "favorites" in case we have problems with any of our other appliances. Thanks Parts Select. :)
The nut was split down one side, so I first tried to sauder the nut back together. Saudering never goes well for me anyway, but I couldn't get a good enough seal around the nut to make it fit tightly. Then I had to cut off the clear plastic shield to get down in there, just before realizing you could just pull the white wire firmly and it would come loose from the nut. All I had to do then was unscrew the original nut, and screw on the new nut. Then, luckily I had mistakenly ordered an extra clear plastic shield and could replace the one I had previously cut. Dishwasher now runs like a charm!
This was too easy. I pulled out the bottom rack, spread apart the two clips which are at the bottom of the spray arm with my fingers and pulled out the old broken spray arm. The damage was visible. Then I took the new spray arm ( which looked different but still fit nicely) and gently pushed it into place. Done!