FDB635RBQ0 Frigidaire Dishwasher - Instructions

If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

Removed the two bracket screws attaching the washer to the countertop, and removed the kick panel beneath the door. Pulled the washer out enough to access the spring arms. Replaced the broken spring arms, and pushed the washer back into it's space, re-attaching the kick plate, and securing the lock tabs on top of the washer. Used one phillips screwdriver, a #2 tip. That simple.

i just took off the old and poped on the new, it was way to easy! no tools required!

Although the part I ordered was not an exact match, it was a Frigidaire piece and fit onto the spray arm assembley the same way. And if I do say so, it actually seems to clean the dishes better! All I did was clip the new one into place.

I removed the screws from the inside of the door. There are also tiny screws you have to remove that holds the part onto the door. Then I was able to remove the part, unplug the power receptacles and install the new part. Very simple!!

two screws, and pull unit out from under counter, turn on it's side. Two allen-head screws to remove motor retaining clip, unplug wires, and remove motor. Reassemble, using silicone grease on O-rings that seal motor. That's it.

I unclipped the plastic pieces at the front of the rack. This was very easy. Then I removed the old rack. I then removed the water sprayer from the old rack and placed it on the new rack. This was simple and I unscrewed the water sprayer by hand and snapped out. Putting it on the new assembly was very easy. Then I placed the new rack on the two stainless steel sliders and refastened the plastic clips at the ends. It was no problem.

First point of leakage was the door. Turns out that a gasket at the bottom of the door functions as a wave trap. As the bottom sprayer spins it sprays against the door and creates a small wave of water this gasket was starting to disintegrate, it was letting water surge over the small tray at the doors bottom. Easy to replace just pull down and remove press fit on inside door bottom. Only when this was replaced did I find the real leak but not until I guessed at the tub seal as the leak. Very hard to see where the water really comes from! Turns out it was not the tub seal but a clip that holds the heater element got smashed down from a dropped dish rack at some earlier time and this caused the heat to increase at the clip and eventually heat the clip to extent it melted the tub directly under it. JB Weld to the rescue and we have a waterproof tub again. Well almost! The tub gasket resisted my best efforts to seat correctly and thus required a new tub gasket, still hard to seat but after 2-3 attempts we have a winner. Total cost about 50 bucks vs. 6-700 for a new unit. Wife is happy!!

Removed damaged strike plate from dishwasher and screwed new part into place. Tested and dishwasher worked fine. Took less than 15 minutes to get the job done. Was very pleased with how fast the part was delivered.

VERY simple---unscrewed three screws on the broken part (the little nubs that held on the bottom spinner were broken off), screwed the new one back in, re-attached the spinner.

I was VERY pleased with the customer service and quick shipping (ordered on Sunday night, the part was delivered Wednesday morning). I would definitely recommend this site to anyone, and would use it again. Five Stars!!!!

Used pliers to remove old seal. Keep seal in position, note the notch facing the hole. Align the new seal, press it in, the notch helps align. Mine slipped in easy

After moving the dishwasher out from the cabinetry, I removed the screws holding the pump in place. Pulling the pump from the formed plastic opening, I found a toothpick lodged in the pump housing. At the same time I noticed that the front o-ring was deformed due to being the incorrect size (too large). It was installed at the factory this way.

I went online to search for new parts. PartSelect was the second or third listing on the search page. I submitted the dishwasher model number and was taken to a set of parts illustrations. I was easily able to find the o-rings I needed.

Turned off elecrtic and water to dishwasher and pulled dishwasher out from under cabinet. Removed broken hose using pliers to open hose clamps.
installed new hose.

I followed the previous repairers instructions.
-Remove the screws around the door panel
-Remove the door panel face
-disconnect the wires
-reconnect wires to the new Latch Assy
-tighten the screws and reassemble the door panel.