Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FDB635RBQ0

FDB635RBQ0 Frigidaire Dishwasher - Overview

Get Parts and Repair Help for FDB635RBQ0

If you know the dishwasher repair part you need, you can browse the list of all parts on the FDB635RBQ0, or you can search by name or part description. You can also find your part by where it is located on the FDB635RBQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for FDB635RBQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.15

Bottom Door Gasket

This gasket is found at the bottom of the dishwasher door and helps prevent water from leaking from the bottom edge of the dishwasher door. If your dishwasher is leaking water from...

Order within the next 9 hrs and your part ships today!
$14.50

Tub Gasket - Gray

This dishwasher door gasket creates a seal around the dishwasher to ensure that water is not able to leak out. If this was not in place there would be a gap between the opening of the dishwasher tub and the outside of the door. If this has torn, you might notice leaking water coming from your dishwasher or the inability to shut the door properly. Simply pull out the current gasket, ensure the area is clean, look for the indicator on your new gasket to determine the middle, and press into place without stretching the material. After the repair is complete, shut the dishwasher door and leave closed a few hours to ensure it properly seals into place.

Order within the next 9 hrs and your part ships today!
$53.02

Lower Dishrack Assembly

This white lower dishrack assembly comes with eight light-gray rollers for easy access. The dishrack is approximately 21 inches wide x 22 inches deep. The dishrack holds dishes in ...

Order within the next 9 hrs and your part ships today!
$25.92

Water Inlet Valve - 120V 60Hz

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close according to the desired amount of water needed. The water inlet valve on your dishwasher supplies water to the dishwasher. If your dishwasher is leaking because it has overflowed, the water inlet valve may be the cause. If your dishwasher continues to fill above the heating element, try opening the door latch to see if it stops filling. If it continues to fill, then you have a defective inlet valve that will need to be replaced.

Order within the next 9 hrs and your part ships today!
$41.87

Upper Dishrack with Wheels

The upper dishrack, a vital part in a dishwasher, holds the dishes in place as the dishwasher goes through its cycle. If the wheels are missing/broken, the upper rack is damaged, o...

Order within the next 9 hrs and your part ships today!
$3.52

Heating Element Brass Nut

The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. Replacing the nut is an easy job, does not require any specialty tools, and should not take you more than 10 minutes. For our step by step guide, click the video below. The brass nut measures 7 inches in length x 1 inch in width x 5 inches in height, and fits most dishwashers. To see if this part is compatible with your dishwasher, check the list of compatible brands below.

Order within the next 9 hrs and your part ships today!
$28.52

Lower Spray Arm with Shield

Located on the lower half of the dishwasher, the lower spray arm rotates and sprays water to clean the dishes in the washer. It does this when water is pushed through the spray arm...

Order within the next 9 hrs and your part ships today!
$18.98

HOSE

If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drainage. This white and black plastic hose is 7.5 feet long. For this repair, you will need either a 1/4-inch or 5/16-inch nut driver, depending on your model. You will need to remove the lower access panel on your dishwasher to complete this repair; it is often easier to remove the dishwasher from the cabinet to do so. Be sure to disconnect the dishwasher from both the power and water supply before completing this repair.

Order within the next 9 hrs and your part ships today!
$26.87

Door Spring

Sold individually.

Order within the next 9 hrs and your part ships today!
$34.50

Delivery Tube Gasket

Sold individually.

Order within the next 9 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking from Inlet Valve

  • Customer: CHRIS from ROANOKE, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 555 of 566 people found this instruction helpful
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first ... read more

Lower Rack Roller Missing

  • Customer: Sandra from Mount Vernon, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 365 of 367 people found this instruction helpful
Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new. read more

Leak in the water inlet valve/solinoid

  • Customer: Mickey from Ooltewah, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 140 of 152 people found this instruction helpful
1. Shut off water supply.
2. Removed inlet water hose where it connects to the vavle assembly.
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection from the solinoid.
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical con... read more