F44P21ATD3 Frigidaire Refrigerator - Instructions

Removed shelves ,removed panel on interior back wall with Philips screwdriver ,unplugged wire terminals slid thermostat off coil ,then reversed process to complete installation.

I called the repairman who diagnosed the problem as a thermostat then had to order a thermostat took about 2 weeks to get back and install (cost little over $100). did good for about two weeks and same problem reoccured. I decided it was defrost timer and ordered from this site for $19.95 including shipping. I got on ( you tube ) and got instructions(recommend you tube) for DIY install about 15 to 20 minutes. Has been running great for about 3 weeks. ( YOU TUBE IS GREAT FOR A DIY REPAIR ON ABOUT ANYTHING)

Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.

Removed existing part, tested it, found it to be defective. OrderEd a new one and replaced the existing one.

a handyman made the repair. It went fine.

I removed the plastic shroud on the ceiling of the refigerator, unscrewed and unplugged the old defrost timer, and replaced it with the new one. I reinstalled the shroud with the new timer installed.

Our old gasket was shot to hell, so we figured we'd replace it to see if that would solve the problem. We followed the instructions of another customer. We realized it was better if we removed the entire door in order to attach the gasket. That took a little doing, but it was totally the way to go. Miracle of Miracles, the leaking has stopped, the food is super cold, and I couldn't be happier.

The defrost timer is faily easy to replace, first unplug the unit, then remove the toe gaurd, then lay on the floor with your light and phillips screwdriver, locate the 2 screws at the lower left side, remove them and the timer and it's shield will drop down. unplug the old timer, plug the new one in and re-install everything. The temp sensor is located in the back of the freezer compartment. Again make sure the unit is unplugged, remove freezer shelves and lower basket, then with a 1/4" nut driver, remove the screws holding the rear panel on, remove the panel and locate the sensor on the upper evaporator tube, unclip it and disconnect the 2 wires, reverse procedure and plug it back in. Not to get on a soap box, but this is the 3rd time i have had the same problem with this unit, plus several other problems.

Removed the back panel of the freezer. Unplugged the defrost cycle thermostat and replace with a new one.
Removed the bottom cover in front of the refrer. removed the defrost timer, plugged new timer in. manually tripped the defrost timer. checked the defrost heater for operation. Checked OK, replaced covers, works like a champ

I followed the directions, which were very simple and easy to follow. The whole process was easy and fast. Couldn't be happier.

Remove front cover below door, remove 2 screws attaching the defrost timer to the refrigerator frame.
Unplug wiring harness plug from timer an install new one.
Remove metal cover in back of the freezer compartment. unpug the two wires going to the thermostat, remove the thermostat { thermostat is held onto the cooling coil with a clip} , remove thermostat and replace with new one

Followed someone before me instructions. very simple and easy

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Heard the snap of a short circuit followed by a burning smell around the refrigerator. Pulled it out, unplugged it and removed the back panel with a nut driver. Plugged it back in and when the compressor kicked on I saw sparks and some smoke at the relay. Unplugged and ordered new relay and the associated run capacitor in case it was also bad.
Removed the holding clip and the relay with capacitor easily came out with two wires attached. Removing the wires was done by prying with needle nose pliers with some difficulty.
Inserting the wires into the new relay was also difficult. If the position isn't just right it does not snap in. Once it is positioned correctly it makes a positive connection with not much effort.
Reassembled the capacitor, plugged unit into compressor, added retaining clip and plugged in refrigerator.
Compressor started up correctly. Note that as the refrigerator cools the compressor will shut off for long periods of time. This is normal.