F44C19IBW0 Frigidaire Refrigerator - Instructions

Like another post, the start relay rattled like a baby rattle. Replaced the start relay and freezer works great.

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.

i looked byhind the freezer , the mottor has the relay connected to it.i took out the relay, and i descovery something was loose inside, i decided to take to check out at sears to see if they have in stock that especific relay. they did not have, they could order, that's when i dicided to go ahead and looking for in the internet, good i found PARTSELECT,they had the part and i was very nice attended,they sent in 2 days i had fix my freezer. thanks PARTSELECT. gilmar couto.

1. turn off the refrigerator using the inside temp dial
2. take all food out of the refrigerator door
3. pull up the gasket along the door frame and loosen all
the screws starting with the bottom and the sides
4. loosen the screws underneath the gasket on the top of
the door (be ready to lower the door frame when you
loosen the last screw!)
5. pull the old gasket off the door frame
6. put the door frame on the floor insulation side up
7. lay the new gasket out on the floor and use a blow
dryer to heat the new gasket to make it flexible
8. put the new gasket on the frame by fitting the crease
of the gasket over the edge of the frame making sure
that the magnet side of the new gasket is facing the
refrigerator when the frame is re-attached
9. apply RTV Silicone sealant along the entire lip of the
gasket (on the insulation side of the frame) and press
the gasket to the frame to form a bond ( I got a tube
of RTV silicone at Wal-Mart in the automotive dept. near
the motor oils)
10. wait 5-10 minutes to let the silicone bond to the frame
11. lift the frame up and re-attach to the door starting
with the top middle screw first, the side middle screws
next, the bottom middle screw last (you may want to get
a second person to help hold the frame while you are
attaching these initial screws)
12. go back and re-attach all remaining screws
13. close the refrigerator door and check for a good seal
all along the gasket
14. your done!

Note: you may want to close the refrigerator door and block
it with a chair to keep in some cold air after you
remove the frame to install the new gasket

I put the refrigerator and saw that the fan wasn't working so I change the fan and the problem still the same. I order a timer and thermostat and change them, nothing change so I order the capacitor and when I remove it I saw that the relay swith was burn out so I order a switch and evarything is ok.
The problem when the fan broke the compressor overheat and burn the swich.
I learn a lot and still saving money over these repair guy.

Thanks

I basically followed the instructions offered when i searched for the ice maker. It was relatively easy to do, I undid the 2 screws holding the ice maker to the side of the freezer, the was the tricky part, holding a mirror so i could see the slots of the screws. loosened them, disconnected the electrical connection and reversed the process for the install. It took about 25 minutes and i was back making ice.

I pulled out the old pieces and poped what I couldn't into the foam insulation behind the support. Then I placed the new piece in the hole and popped the plastic pin to seat the support. bang. the only problem I had was knowing if it was the right part by the picture. The little pin that had to be pushed through kinda threw me.

I removed the plastic cowl in the rear of the freezer to gain access to the fan, took out two screws that secured the brackets holding the fan. Then I separated the coupling wires which had a sort of locking mechanism that was simple to undue. I took out the brackets along with the fan, separated the brackets and removed the screw for the ground wire. Then I simply reversed the process.

Did the obvious. Removed the stick-out cover, then the back of the freezer wall, after taking the bad evaporator fan out. Replaced the old motor with the new one, stuck the fan blades back on, and put the replacement back in place. Checked to see that the new motor and fan, before final hook up, had no issues. That was a success. However, when I put the parts in place, I had some significant vibrations. By taking things apart and re-doing the install, the vibrations went away. However, the final install, even if quiet, did not work. Apparently the condenser was kaput. No cooling after all the adjustments. We gave up and are replacing the fridge.

Twisted replacement bulb into place easily. Let there be light!

it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.

Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness.
Installed the new one in reverse order and works like a champ.

Removed the old and installed the new. Electrical plug/socket made connection easy. Biggest problem is working space in freezer side of a side by side with the fan in the back. If I can do it anyone can.

Removed old thermostat and replaced. really easy.