F21C445CS2 Frigidaire Washer - Instructions

After struggeling the most with lifting out the inner drum and then the wash drum. I realized when the job was complete a better way. 1. Take the top off the washer. 2. take the front off the washer. Then disconnect all wires and hoses from assembly One small hose on the tub and the pump hose at the bottom. 3. at the bottom of the overall assembly there are 3 braces holding the tub assembly with 2 springs on each brace. Go under and remove the springs and then lift the whole assembly out into the middle of the floor. 4. remove the top cap off of the agitator. 5. remove the agitator. 6. if you are lucky and the bolts are not seized in the block that holds the shaft remove the small steel block from the bell and remove the bell. 6. Slide the inner tub up and off the shaft and again if all goes well the outer wash tub should slip up off the shaft as well. 7. remove the drive belt from the motor and transmission.

-Remove front panel - 2 screws
-Remove the top panel - 2 screws
-Disconnect the lid switch from the top panel - 2 screws
-Remove the agitator cap - unscrew
-Remove the agitator - This was a bit difficult and required a lot of jiggling but it eventually came off
-Remove the inner drum - 5 bolts at the bottom
-Remove the drum mount - 2 bolts and then it got really difficult. A lot of penetrating blaster, wire brushing, jiggling, and some strategically placed hammer taps (don't damage the threads.
-Remove the seal
-Clean up the inner and outer seal seating surfaces
-Rinse and repeat in reverse (pun intended)

unplugged machine. pried up with large regular screwdiver on top washer lid. removed two phillips screws bottom of front panel, had to use rubber mallet to drive front panel down to remove as was rusty and old. removed old belt using screwdriver. put new belt under tub pulley and put belt on small pulleys. kept moving tub and springs by pushing on tub. Took several tries to get new belt to go on the large tub pulley but finally did it. I used the instructions you gave for replacing broken drive belt and it worked. replaced front panel and two phillips screws, put top back on and away it went.

I push the new knob onto the post that fit the knob

Loosened top of washer from spring tabs and leaned it against wall, removed two phillip head screws from the front bottom panel, removed panel. Removed spring clamps from 2 hoses( make sure water is drained from tub before doing this!!) on pump, removed 2 wire connectors. Used nutdriver to remove 2 screws that held down pump. Replaced pump and everything else installs in reverse. Almost forgot, the plate that holds the pump to the bottom of the washing machine has to be removed from the old pump and attached to the new one.

Tilted the clothes washer back to provide easy access. Then after scrubbing the floor - which took most of the time of the repair, screwed out the broken leg and screwed in the new leg or SCREW. Easy peasey.

ordered the new pump,its a lot more heavy duty than the orginal.had to change the mounting bracket somewhat. the new pump mounted bythe bottom of the pump housing and theold pump mounted by the side of the pump housing. so, wnere the curve was in the mount, I used the bench grinder to cut the curve out to make a flat surface for the new pump to rest in ,also drilled two 1/4 inch holes in the mount for the bolts to mount the pump.

Disconnected power, removed hoses, removed housing and pump. Re oriented drain pipes on pump to align with washer hoses (just twist collar and re set) attach foot bracket and secure to washer bottom. Attaching the hoses with the compression clamps was a bit of a problem until I used pliers to press the ends together and then an adjustable wrench to hold them tight. Slid on hoses and released clamps. Replaced electrical and secured pump cover. Done in about 15 minutes.

remove one hose clamp.pulled hose from back of washer.replaced with new hose in same procedure.best of all i had my new hose in two days.great serviceand inventory.

I just removed the broken foot with a pair of plyers and screwed the new one on. The decorative side panel popped right into place.

Disconnect power,take water hoses off using pliers,they are really tight,remove 2 philips head screws,pull 2 wire connectors off and water fill hose squeezing wire clamp and sliding clamp back on hose.reverse to install.Works like a champ.

Pump replacement quite simple - most difficult part of job was figuring out how to disassemble outer washing machine panels. Pump required disconnecting 2 hoses and an electrical connection.

removed top cover to access valve dissconnected hoses and wires then unscrewed valve and replaced

Poped up top, removed front pannel (2 phillip head screws) observed failed belt. Replaced belt. Tensioner can be held back by hand so it was easy. Works great. Part Select Rocks! I put in the model number and bam, there was my needed part, 3 days later it was in my hands. This was after me wasting time driving around town trying to find it at home depot type stores to no avail. I'll never do that again. This website makes repairing appliances a snap. Gotta love on-line shopping! woo hoo

we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing