Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
If you know the refrigerator repair part you need, you can browse the list of all parts on the ESS22XGMBBB, or you can search by name or part description. You can also find your part by where it is located on the ESS22XGMBBB by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ESS22XGMBBB parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...
This temperature sensor, also known as a thermistor, is used for refrigerators and freezers. The sensor sends the temperature reading of the refrigerator towards the control board. If your refrigerator or freezer runs too long, is too warm, will not defrost, or has sections that are too cold, replacing this part is the solution. Before replacing the temperature sensor, make sure to unplug the fridge for safety. The tools needed for this repair are a nut driver, wire crimper, and wire splice connectors. Search your model number to ensure the correct part is ordered and refer to model specific diagrams/owners manual for the exact instructions.
When activated, the auger rotates and pushes ice out of the bin through the chute to the user.
This defrost termination thermostat acts as a safety device to stop the evaporator coil from overheating, by turning off the defrost heater at the end of the defrost cycle. The thermostat measures the temperature in your freezer to ensure that it stays at an optimum temperature to keep your frozen food from thawing. Some common symptoms linked to a faulty defrost termination thermostat include: the freezer is not defrosting, is too cold/too warm, or there is a frost build up in the freezer. Before you decide to replace this part, ensure that there is no frost build up in your freezer; as a build up can interfere with the thermostat reading.
This double outlet water valve has quick connections. This valve has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.
The drawer slide rail for the right side is used for refrigerators. The drawer slide rail attaches horizontally to the refrigerator wall and supports the drawer so it can easily slide in and out. If the drawer slide track is broken, not sliding, or is not dispensing water, then changing the right side drawer can be the solution to the following problems. Make sure to unplug the refrigerator from the power source and make sure to wear gloves to protect your hands when installing. Refer to the diagram provided by the manufacturer for further guidance and instruction.
When looking inside the fridge, this white drawer slide rail is located on the left side of the refrigerator. Rail ONLY.
If you notice that your refrigerator or freezer is noisy or too warm, you may need to replace the evaporator fan grommet. This part is red in color, and is about 1 inch in diameter. The evaporator fan grommet is located behind the evaporator fan cover in the back of the freezer. You will need to remove the evaporator fan cover to access the evaporator fan and complete this repair. Before you begin this repair, ensure the power to the refrigerator is disconnected. You will need a pair of needle nose pliers, a small flat blade screw driver and both a 1/4 and 5/16-inch nut drivers to complete this repair.
This is an ice and water filter. The most common reason you would need to change this part is if you have never updated your model and it is no longer filtering your water. This al...
The dispenser door assembly (or flapper) is what opens to release the ice once the lever has been pressed. This part mounts in the ice dispenser. The cranker no longer comes with this part. You can use the original crank. The crank is sold separately depending on the model number of the appliance. For this repair, all you will need is a Phillips screw driver and a small flat blade. Disconnect the power, remove the escutcheon from around the dispenser, lift up the control panel, disconnect all wire connectors, use a screwdriver to remove all four screws of the housing, and lift the housing out. You will now see the flapper: push the tabs that are securing it in place to remove the piece, install the new flapper by lining it up and snapping into place.
Fixed by these parts
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.