EMO3000HBB01 General Electric Microwave - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Exytemely loud griding noise
Removed the screws holding base of microwave. Removed two screws from driver motor after disconnecting the wiring from the motor. removed turntable plate to gain access to the shaft of motor and place plastic part on stem of motor. Fastened two screws back in the new motor. Installed screws in base of microwave. Done
Parts Used:
-
BILLY from LITTLE ROCK, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
turntable would not turn
I realized the turntable coupler had broken, but part of it was still in place. I read most of the other installation instructions, and pulled the coupler off. I did not use any tools other than the vacuum. Then I used my wet/dry vac to try to get the broken piece out that had fallen to the bottom of the microwave. I was unable to get it out. I put the new coupler in place (has a half moon base you should line up with the center) and I pushed down until I heard a click. Turntable works good as new! Simple, easy, if I can do this, anyone can. Reading the other responses was helpful. Easy order/quick delivery. Would recommend to friends/family.
Parts Used:
-
Judy from Powder Springs, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broke the cooking tray and turntable coupler
Popped the coupler on and put the cooking tray on top of the coupler.
Parts Used:
-
CYNTHIA from BEAR, DE
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Micro turntable was not working properly.
I watched the video on how to replace the motor and it was as simple as you said it would be. Just need the correct short handle screwdriver. It is very simple and easy. Thanks for the video.
Parts Used:
-
Barbara from Tamarac, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Bulbs were ole and broke off inside socket
Took the light socket out and replaced it.
Parts Used:
-
William from Columbus, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burned out microwave light bulb and base broke off in light socket
Replaced light socket and bulb. Real easy repair.
Parts Used:
-
KENNETH from STRONGSVILLE, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
turntable noise turned slowly
lowered bottom cover removed wires from motor removed two screws from motor put in new motor and put cover back on with the six screws that held it on. plugged cord back into outlet. very good instructions and very easy to install. my wife was impressed.....recieved part qiuckly very good service.
Parts Used:
-
gary from tupper lake, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Glass tray broke
-
Vicki from Mokena, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Drive motor not working for the turntable
-
Rick from clermont, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
turntable not turning
-
Chris from Platte City, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The turn table quit rotating
The microwave is mounted above the stove. I left it in place while making repairs. I unplugged the microwave. I removed 3 phillips head sheet metal screws, bottom front and 2 phillips head screws bottom rear. The bottom cover swung to the rear of the microwave and hung on hinge tabs. I popped the turntable coupler up and off with a table knife. I removed 1 screw on the drive motor and slid it out of a slot on the other side. I pulled of the electrical plug and installed the new drive motor and turntable coupler. This is a really easy repair.
Parts Used:
-
Robert from Florence, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Turning plate making horrible grinding sound
I removed the bottom plate of the microwave, unscrewed and unplugged the motor, screwed in and plugged up the new motor. VOILA, DONE! $40 is lot better than $350 for a new microwave. Thanks PartSelect.com.
Parts Used:
-
Kay from Mc Alpin, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
turntable would not turn, noisey
-
Wilton from Lamar, SC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Part came with a "lip" on the side sticking out.. instead of being smooth...It did not fit
I could not repair this by myself..Thank goodness I have a "go to guy" who came and "fixed" the problem..I was told that this was not the part needed for this turntable..did not need this "extra piece sticking out of the side" with this extra thick "lip" sticking out of the side of the coupler, the coupler did not fit..Thank goodness for my "go to guy"...
Parts Used:
-
Helene from Garnerville, NY
-
Difficulty Level:Very Difficult
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Vent grille mounting hole brooken
Screw driver to remove two screws all the tools needed. Part was expensive (microwave new was $250 and vent grill was $89). Recieved part within 48 hours after ordering with ground shipment. (Quick)
Parts Used:
-
Clinton from Orange Park, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!