EMO3000CCC03 General Electric Microwave - Instructions

Repair went exactly as described on line. . . Total of seven screws. . . Five to remove the trim and exposed the drive motor and two holding the drive motor in place. . . A magnetic screw driver would have been helpful but not necessary. Almost took more time to find the correct circuit breaker than time to do the repair.

Remove 2 screws, remove cover, remove filter, reverse proceedure.

change fuse still didnt work i saw enougher fuse put the new fuse in there old fuse back and it didnt work . it was easy to do but it didnt fix proplem lihgt bulb didnt change coudnt figure how to find were it went

After seeing that a replacement microwave would run at least $250 or more, I researched the problem online which included instructions on how to replace the motor and determined that the repair would be a somewhat easy Fix-It-Yourself project (and a whole lot easier than replacing the entire unit!). I ordered the turntable motor for under $40 at this website, it came within a few days. I printed the instructions from the webpage noted above and took them and a phillips-head screwdriver to the microwave, and I had the repair done in less than 10 minutes with my wife helping hold the bottom panel in place while I put in the 5 screws.

Dropped bottom of microwave, removed motor then installed new motor. Very simple.

I followed the directions posted by others - they were perfect. This was a very easy process. The screws on the motor were hard to take off because they were put on at the factory with equipment is my guess. But the process was very easy. The turn table is working. I still have the noise but now realize that is from the magntron fan, which I am not going to replace given the age of the microwave. At least my food is heated evenly with the table turning and I can live with the noise until I see the price I want to pay for a replacement microwave. Thanks all!!!

Found blowup drawings inside unit, which helped identify what I had to remove. Had neighbor assist in lifting unit from wall mount, unit slides easily from rails once top bolts are removed. Pay attention to where all the screws go as you remove them, some inside assemblies will have to be removed or loosened. A good guideline to go by is all black screws hold internal assemblies, the bronze screws go in the back side and the chrome screws go on top, sides, and front of the unit. I was able to lift unit back on rails without any assistance.

Just like your video. Used putty knife to remove the inside trim. unscrewed handle and put screws in new handle,pushed in the trim and it was done.

Removed microwave bottom cover ....removed motor....replaced...parts fit perfectly...your-company is the best...service, price & support!

removed access panal, found soft switch as discribed on your web site. removed and replaced.

Removed the bottom plate screws from the microwave. Disconnect the wire harness. Replacement of the light sockets is easy. The female terminal connectors that connected to the bulb sockets were corroded, so I had to go to the hardware store and get replacements for those also. Replacement of those was unexpected but straightforward.

1) I unplugged the microwave. 2)I removed 5 screws which allowed the bottom of the microwave to open. 3)I unplugged the drive motor. 4) I removed 2 screws holding the bad motor and removed the motor. 5) I installed the new motor with the same 2 screws and completed the replacement by doing steps 3,2,1. I reset the clock after testing. Easy-Peasy. My mother was thrilled. She was using it that way for about a year because she thought a repair person would charge too much.

Opened the bottom panel of the microwave, removed one screw from the motor, rotated motor aprox 1/8th turn and pulled it down, Pulled off wires and then reversed the operation. Was easy and works great. I was really surprised how fast the new part was sent.

unplug microvave,remove 5 screws from bottom of microvave. Motor is in the center. unplug remover remove last screw. replace motor plug motor back in and reverse steps. so easy!

PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.