Models > EL5030VW1 > Instructions

EL5030VW1 Roper Dryer - Instructions

All Instructions for the EL5030VW1
1501 - 1514 of 1514
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replaced Belt
The online vidio was very helpfull
Parts Used:
Multi Rib Belt - 92-1/4"
  • MARCUS from MACON, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
the dump would not stop running.
Replace the switch in diagram #4.
Parts Used:
Dryer Thermal Fuse
  • modean from Clermont, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer tub drive belt broke
Unplugged the power cord. Removed two screws on lint vent , used putty knife to release clips to raise top at front of unit. Disconnected the plug from front door switch. Laid dryer on its back. Removed two screws to remove front including the door. Vacuumed lint from inside unit. Installed belt temporarily using two pieces of masking tape to hold it in place while properly routing the belt. Gave the tub a full turn to insure alignment.. Reinstalled the front of unit with the two screws. Righted the unit and snapped down the top. Replaced the two lint vent screws. Plugged it back in and done! Piece of cake!
Parts Used:
Multi Rib Belt - 92-1/4"
  • Ray from Salisbury, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The dryer wasn't heating.
Unplugged the dryer... a 220 shock can be deadly. I removed the back of the dryer using the nut driver. Using a needle nose pliers I removed the electrical connecters from the thermostat. The thermostat fell apart in my hands.. Easy diagnosis. I continued with disconnecting all wiring from the heating unit (thermal cut off also)and removed. There is an upper screw on the unit that needs to be removed (it is kind of difficult to do), I used a wrench set with a 1/4" drive. Then just lift and pull a little towards you. I inspected the heating coils for breakage. There were none. Being as this unit is 25 years old and not repaired before, I decided to replace the Thermal cut-off, thermostat-250F, and the thermal fuse. All three could have been a culprit in this case, even after the obvious. Putting it back together is the opposite of taking it apart. SUCCESS....$80.00 repair vs $499.00 for a new one. By the way... clean out the lint while you have it apart.
Parts Used:
Dryer Thermal Fuse High Limit Thermostat Thermal Cut-Off Kit
  • Marta from Battle Ground, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Washer overflowed
Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.
Parts Used:
Leveling Foot
  • Beth from Valley Springs, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer wouldn't turn on
When the part came in. I unplugged the dryer. Pulled it away from the wall and took the back off. I pulled the wires off the old fuse and plugged them in the new fuse, then unscrewed the on nut that held the old fuse. Then slid the new one in and put the nut back on. Plugged the dryer in and it worked. So I unplugged the dryer and put the back on.
Parts Used:
Dryer Thermal Fuse
  • pamela from ocean springs, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer turned but no heat
Unplugged dryer from wall. Removed screws from the back using the socket set. Removed thermostat screws and disconnected wires(one at a time) while replacing new thermostat. Replaced second thermal and tightened screws. Replaced back panel on dryer. Plugged in, turned on and dryer was repaired..
Parts Used:
Thermal Cut-Off Kit
  • Tarcia from Buford, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!
Noisy tumbler & worn lint trap seal
Followed procedures in Parts Select web site video
Parts Used:
Rear Drum Support Roller Kit Lint Trap Housing Seal
  • Pedro from Brunswick, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer Ran -No Heat
Watched video on locating and testing parts (did help that I had a digital meter w/cont-tone ) removed and cleaned out dryer cabinet tested heating element-was ok went to thermal cutoff (tested bad ) ordered kit from part select parts arrived within two days (fantastic ) replaced parts in thermal cut off kit . Replaced dryer back also and important -removed dryer vent and cleaned out pipe -replaced vent pipe turned on the power tried dryer works like new again your easy to follow instructions made this a very easy job thanks people ! You saved me a great deal of aggravation and more important money
Parts Used:
Thermal Cut-Off Kit
  • John from WEST CHESTER, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer would run, but not heat
Removed the back panel, found the fuse and replaced it. Easiest thing I've ever done! I was expecting it not to be the problem, but I started with the "most common" issue via the website. Voila...it was the problem!
Parts Used:
Dryer Thermal Fuse
  • Kenny from Euclid, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Plastic catch broke
little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install
Parts Used:
Door Catch Kit
  • Charles from North Chesterfield, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Indicator lights blinking, not drying, auto settings not working
Unlike your video, with this model, the thermal fuse is located near the front of the dryer, which I didn't find out until the back was already off.
Parts Used:
Dryer Thermal Fuse
  • James from Frankfort, KY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
dry door latch broke
I watched the online video first, which made the removal and installation fast and easy.
Parts Used:
Door Catch Kit
  • George from Melbourne, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Parts Used:
Heating Element Connection Wire Kit
  • Betty from Erie, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the EL5030VW1
1501 - 1514 of 1514